Santec ECL-210 Скачать руководство пользователя страница 46

Страница: 46 / 96

EXTERNAL CAVITY TUNABLE LD LIGHT SOURCE ECL-210

7-9

9-4Å@îgí

∑

ÇÃê›íË

9-5Å@MLSÇÃMODE

APC

COH

CURR TEMP POWER WAVE FINE

7.4. Selecting a Unit in MLS

When the units are inserted into MLS, it is required to select the unit controlled. When looking

at the front of the MLS unit the slot on the farthest left hand side is numbered one. The MLS-2100

has two slots numbered one and two, the MLS-8100 has eight slots numbered one to eight. When

operated through the the communication ports, these assignments become A and B for the MLS-

2100 and A to H for the MLS-8100. (details are given in Chapter 9). The selected ECL-210 unit

is shown on the unit selection display. To change the selected slot, push the key [CHANNEL]

each time the slot number selected at present enables to shift the slot number inserted to right

direction. When the very right slot selected, it goes back to the very left slot number. The condi-

tion becomes waiting for parameter display and key input after unit is selected according to the

MODE set up in the previous time.

If MLS is operated without CHANNEL confirmation, the wrong unit is selected and the param-

eters are changed. Be sure to confirm the CHANNEL number in setting parameters and moni-

toring. Especially, [STORE] key.

NOTE

The MLS display, parameter setting, monitoring, and control ON/OFF, are controlled by MODE.

The present MODE is shift-selected to right direction by [MODE] key. The present MODE can

be recognized with LED. Each key and shuttle switch are active for the display and operation

which are prepared on each MODE.

7.5. MLS Mode

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды