Santec ECL-210 Скачать руководство пользователя страница 25

Страница: 25 / 96

5-2

ECL-210 Operation Manual

(1) Light source unit insertion slot

Each unit or blank cover is loaded on.

(2) Fixing screw hole

This is a hole for fixing each unit or blank cover.

(3) Blank cover

Insert the blank cover to an empty slot. If the blank cover is not inserted, the system may

not work stably for heat generated.

(4) Unit fixing screw

This is the fixing screw for each unit or the blank cover. When pulling out the unit, pull

slightly with loosing the screw.

(5) Parameter display

This indicates the parameters of each unit and MLS communication parameters.

(6) SHIFT key

This is the key for toggle movement (SHIFT ON/OFF) to ordinary status and MLS

SHIFT status.

(7) SHIFT_LED

This is lit when the MLS status is SHIFT.

(8) ON/OFF key

When this key is effective, pressing this causes ON/OFF toggle movement settled in each

MODE.

(9) Shuttle switch

This is for setting and monitoring parameters. The parameter goes up/down and the

speed can be changed by angle.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание ECL-210

































































































Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды

Santec ECL-210, Руководство по эксплуатации

Результаты поиска

Содержание ECL-210

Отзывы:

Похожие инструкции для ECL-210

Бренды по названию

Популярные бренды