background image

 

PLANNED MAINTENANCE

—QUARTERLY INSPECTION 

Photo Eye Inspection  

Inspect the photo eye mounting brackets and photo 
eyes for visible damage or misalignment. Verify that 
the photo eyes operate as described below: 

 

Personnel and objects should not be in the path of 
the  door  when  the  following  inspection  is 
performed.  If  the  photo  eyes  are  not  working 
properly,  the  door  could

 

strike an individual 

or object in its path. 

 

1.  Open the door to the fully open position by 

pressing the open 

(▲) key located on the Rytec 

System 4 Drive & Control Panel.  

2.  Place an object between the photo eyes to 

interrupt the light beam between the photo eye 
transmitter and receiver.  

3.  Press the close 

(▼) key on the Rytec System 4 

Drive & Control Panel. The door should not move 
or close at all.  

4.  Remove the object and cycle the door to verify 

that the front set of eyes is working properly.  

5.  If the photo eyes on the door front are not 

working properly, the photo eyes may be dirty. 
Clean the lens of each eye as required, using 
window cleaner and a clean, soft cloth. If this 
does not resolve the problem, see “PHOTO EYE 
ADJUSTMENT-ALIGNMENT

” on page 17 for 

adjustment procedures.  

Refer to “PHOTO EYES” on page 4 for additional 
information on how the photo eyes operate.  

QUARTERLY INSPECTION  

Electrical Inspection  

CONTROL PANEL, ENCODER, AND MOTOR 
WIRING 

 

The  disconnect  must  be  in  the  OFF  position  and 
properly locked and tagged before performing the 
following procedure. 

 

1.  Inspect electrical connections to the power drive 

assembly and encoder assembly.  

2.  Inspect control panel wiring. See Rytec System 4 

Drive & Control Installation & Owner’s Manual for 
control panel inspection procedure. 

UPPER JUNCTION BOX 

NOTE: The upper junction box is an optional item 

that may have been installed during the 
installation of your door. If an upper junc- 
tion box was installed, it was most likely 
mounted on the wall, just above the control 
panel. If your door has an upper junction 
box, it must be inspected. 

 

1.  Move the door to the fully closed position. 

2.  Remove power to the control panel by placing 

the fused disconnect in the OFF position. 

 

The  disconnect  must  be  in  the  OFF  position  and 
properly locked and tagged before performing the 
following procedure.

  

3.  Remove the cover from the upper junction box 

located above the door opening. (See Figure 17)  

4.  Inspect all electrical connections in the upper 

junction box. All connections must be tightly 
secured.  

5.  Check for pinched, kinked, cracked, or damaged 

wires and insulation. Repair or replace wires as 
needed.  

6.  If the door is configured with the optional defrost 

system (heat tapes), inspect all associated 
electrical wiring and connections. Repair or 
replace wires as needed.  

 

Figure 17 

7.  Replace the cover.  

8.  Apply power to the door.  

Rework this 

Figure

 

Bi-Parting Door Shown 

One-Way Door Is Similar

 

System 4 

Control 

Panel 

Upper 

Junction 

Box 

Fused 

Disconnect 

Содержание Turbo-Slide



















































Отзывы: