RTS KP-12 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 106

RTS KP-12 Скачать руководство пользователя страница 21

3-3

at the remote location if your keypanel has the lower trunk IFB priority. IFB trunk priorities are
set in ADAMedit. (Click the "KP" button on the ADAMedit toolbar to access Keypanels / Ports
setup, then click the "Edit" button, then click the "Advanced" tab. Enter the desired IFB priority in
the fields provided. Be sure to send the change to the intercom system.)

Flashing Green Talk LED & Display Alpha (on time equal to off time)*

There is an incoming call from the destination assigned to the key. Activate the key to talk back.

Note

The duration of incoming call flash is controlled by DIP switch 4 on the KP-32 back panel. See
"Option Switch Settings" for further information.

Winking Green Talk LED (on time less than off time)*

This indicates that a key is ready to talk (key is on), but requires external footswitch activation to talk.

Listen LED Indication

The listen LED is the upper LED for each key. The listen LED is green when listen is on.

Intercom Key Operation

Basic Intercom Key Operation

The "up" position of an intercom key activates listen (if assigned). The "down" position activates
talk (if assigned). If there is no talk assignment for an intercom key, the talk position of the key
will not activate. If there is no listen assignment, the listen position will not activate.

For momentary activation of a key press and hold the key. Then, release it when finished.

For latching operation (if enabled) tap a key; it will turn on and remain on. Tap the key again to
turn it off when finished.

Note

Latching may be turned off for the entire keypanel by setting DIP switch 1 on the KP-32 back
panel to the Closed position. Latching may be disabled for individual keys on a keypanel using
ADAMedit: Click the KP button on the ADAMedit toolbar to open the Keypanels / Ports setup
screen. Select the intercom port where the keypanel is connected. Place a check mark in the "D"
check boxes for any keys where you want to disable latching. Be sure to send your changes to the
intercom system.

Operation of Intercom Keys with Auto Functions

Note

Assignment of keys with auto functions is described in the programming sections that follow.
Descriptions of the auto functions are also contained in the Glossary.

Operation of keys with auto functions is as follows:

Talk + auto follow

Talk and listen can be activated separately. The listen assignment listens to whatever is assigned
to the talk key.

Talk + auto listen

Both talk and listen will activate when talk is activated.

Talk + auto mute

Listen will turn off when talk is activated.

«
...
19
20
21
22
23
...
»

Содержание KP-12











































































































Отзывы:

Нет отзывов