Rosemount 3051S Series Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 190

background image

114

Reference Manual

00809-0100-4803, Rev GA

Troubleshooting

September 2017

Troubleshooting

5.5

Measurement troubleshooting

The transmitter provides a means to display the current process variables and flow calculations. If the
process variable reading is unexpected, this section provides the symptoms and possible corrective
actions.

Table 5-4. Unexpected Process Variable (PV) Readings

Symptom

Corrective action

High PV Reading

Primary element

•

Check for restrictions at the primary element.

•

Check the installation and condition of the primary element.

•

Note any changes in process fluid properties that may affect output.

Impulse piping

•

Check to ensure the pressure connection is correct.

•

Check for leaks or blockage.

•

Check to ensure that blocking valves are fully open.

•

Check for entrapped gas in liquid lines or for liquid in gas lines.

•

Check to ensure the density of fluid in impulse lines is unchanged.

•

Check for sediment in the transmitter process flange.

•

Make sure that process fluid has not frozen within the process flange.

Power supply

•

Check the output voltage of the power supply at the transmitter. It should be 12 to 42.4 V dc for HART with no load at

the transmitter terminals.

Note

Do not use higher than the specified voltage to check the loop, or damage to the transmitter may result.

Feature board electronics

•

Connect a personal computer and use AMS Device Manager, Engineering Assistant Software, or the Field

Communicator to check the sensor limits to ensure calibration adjustments are within the sensor range and that
calibration is correct for the pressure being applied.

•

Confirm the electronics housing is properly sealed against moisture.

•

If the feature board electronics are still not functioning properly, substitute new feature board electronics.

Flow configuration (fully compensated mass and energy flow feature board only)

•

Verify flow configuration is correct for current application

Process temperature RTD input

•

Verify all wire terminations

•

Verify sensor is a Pt 100 RTD

•

Replace Pt 100 sensor

Sensor module

•

The sensor module is not field repairable and must be replaced if found to be defective. Check for obvious defects,

such as a punctured isolating diaphragm or fill fluid loss, and contact your nearest Emerson

™

Service Center.

«
...
120
121
122
123
124
...
»

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

Бренд: ABB Страницы: 8

Бренд: Omicron Страницы: 80

Бренд: QuantAsylum Страницы: 70

Бренд: Velleman Страницы: 16

Бренд: Velleman Страницы: 4

Бренд: Velleman Страницы: 8

Бренд: velocomp Страницы: 4

Бренд: E-Mon Страницы: 72

Бренд: Fluke Calibration Страницы: 13

Бренд: ETI Страницы: 2

Бренд: Aethra Страницы: 2

Бренд: Flymaster Страницы: 7

Бренд: Kane Страницы: 35

Бренд: Veris Страницы: 3

Бренд: Caen Страницы: 63

Бренд: Caen Страницы: 35

Бренд: Hanna Instruments Страницы: 2

American AL-1000

Бренд: Badger Meter Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды