Rosemount 3051S Series Скачать руководство пользователя страница 24

Страница: 24 / 190

Reference Manual

00809-0100-4803, Rev GA

Configuration

September 2017

Configuration

Figure 2-11. Save/Send Configuration Tab (Offline Mode)

2. Select the icon above each window to be taken to the appropriate screen to edit the configuration

information. To return to the

Save/Send

tab, select

Save/Send

in the left menu.

3. When all information is correct, see

“Sending a configuration in offline mode” on page 16

“Sending

a configuration in online mode” on page 17

Note

The user will be notified if the configuration has been modified since it was last sent to the transmitter. A
warning message will be shown to the right of the

Send Flow Data

and/or

Send Device Data

check boxes.

Sending a configuration in offline mode

1. To send the configuration, select the

Send To

button.

Note

The

Send Flow Data

and/or

Send Device Data

check boxes can be used to select what configuration data is

sent to the transmitter. If the check box is unselected, the corresponding data will not be sent.

2. The Engineering Assistant Device Connection screen will appear, see

Figure 2-12 on page 17

Содержание 3051S Series































































































































































































Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды

Rosemount 3051S Series, Справочное руководство

Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды