Rosemount 3051S Series Скачать руководство пользователя страница 109

Страница: 109 / 190

101

Reference Manual

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

Separate the SuperModule assembly from the housing

1. To prevent damage to the SuperModule connector, remove the feature board from the SuperModule

assembly and remove the connector before separating the SuperModule assembly from the housing.

2. Loosen the housing rotation set screw by one full turn with a

-in. hex wrench.

3. Unscrew the housing from the SuperModule threads.

Figure 4-10. SuperModule Connector

-in. housing rotation set screw

Note

The V-Seal (03151-9061-0001) must be installed at the bottom of the housing.

Figure 4-11. V-Seal

A. Black rubber V-seal

Attach the SuperModule assembly to the Plantweb housing

1. Apply a light coat of low temperature silicon grease to the SuperModule threads and O-ring.

2. Thread the housing completely onto the SuperModule assembly. The housing must be no more than

one full turn from flush with the SuperModule assembly to comply with flameproof/explosion-proof
requirements.

3. Tighten the housing rotation set screw using a

-in. hex wrench to a recommended torque of

30 in-lb (3.4 N-m).

Содержание 3051S Series































































































































































































Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды

Rosemount 3051S Series, Справочное руководство

Результаты поиска

Содержание 3051S Series

Отзывы:

Похожие инструкции для 3051S Series

Бренды по названию

Популярные бренды