Rosemount 3051S Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 190

background image

93

Reference Manual

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

To correct for mounting position effects on transmitters equipped with an absolute static pressure
sensor, perform a lower sensor trim. This is accomplished by selecting the

Lower Sensor Trim

button

and following the on-screen prompts. The lower sensor trim function provides an offset correction
similar to the zero trim function, but it does not require a zero-based input.

Upper and lower sensor trim

To perform a Static Pressure Full Sensor Trim, perform the following procedure:

1. Select the

Lower Sensor Trim

button and follow the on-screen prompts.

2. Select the

Upper Sensor Trim

button and follow the on-screen prompts.

Note

It is possible to degrade the performance of the transmitter if the full sensor trim is done improperly or
with inaccurate calibration equipment. Use a pressure input source that is at least three times more
accurate than the transmitter and allow the pressure input to stabilize for ten seconds before entering
any values.

Recall factory trim

The

Recall Factory Trim

button will restore the transmitter to the original factory characterization

curve. The

Recall Factory Trim

button can be useful for recovering from an inadvertent zero trim or

inaccurate pressure source.

When the recall factory trim function is used, the transmitter’s upper and lower trim values are set to the
values configured at the factory. If custom trim values were specified when the transmitter was ordered,
the device will recall those values. If custom trim values were not specified, the device will recall the
upper and lower sensor limits.

Last static pressure sensor trim

The current upper and lower trim points can be seen under the

Last Static Pressure Sensor Trim Points

heading.

Calibration type

The calibration type drop-down menu allows the user to note the type of device last used to calibrate the
sensor (either Differential, Gage, or Absolute). This field does not affect the calibration of the device.

4.3.5

Process temperature sensor calibration

The

Temperature Calibration

tab allows the user to perform a sensor trim and configure the sensor

matching of a process temperature sensor, see

Figure 4-4 on page 94

Mass and energy flow Fast Keys

1, 2, 5, 5

Direct process variable output Fast Keys

1, 2, 4, 5

«
...
99
100
101
102
103
...
»

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

Masoneilan 12400 Series

Бренд: Baker Hughes Страницы: 81

Бренд: Magtrol Страницы: 83

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: palintest Страницы: 14

Pasport PS-2138

Бренд: Pasco Scientific Страницы: 26

Бренд: Flowmetrics Страницы: 102

Бренд: AccuMac Страницы: 10

Бренд: Yamaha Страницы: 12

Бренд: Velleman Страницы: 15

Бренд: Konica Minolta Страницы: 42

Бренд: Kobold Страницы: 12

Micropilot S FMR533

Бренд: E+H Страницы: 12

Бренд: National Instruments Страницы: 169

Intelligizer Fence Monitor

Бренд: Zareba Страницы: 8

HydroTracer FLV HT2

Бренд: aboni Страницы: 48

Бренд: MFJ Страницы: 8

Бренд: B&K Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды