Rosemount 3051S Series Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 190

background image

94

Reference Manual

00809-0100-4803, Rev GA

Operation and Maintenance

September 2017

Operation and Maintenance

Figure 4-4. Calibration - Temperature Calibration Tab

Process temperature upper and lower sensor trim

To calibrate the Process Temperature Input using the sensor trim, follow the procedure shown below:

1. Set up a Temperature Calibrator to simulate a Pt 100 (100-ohm platinum, alpha 385 RTD). Wire the

two red wires from the Rosemount 3051SMV terminal block to one connection, and the two white
wires to the other connection. See

“Install optional process temperature input (Pt 100 RTD sensor)”

for more information.

2. Adjust the calibrator/RTD simulator to a test point temperature value that represents a minimum

process temperature (for example, 32 °F or 0 °C). Select the

Lower Sensor Trim

button under the

Process Temperature Sensor Trim

heading and follow the on-screen prompts.

3. Adjust the calibrator/RTD simulator to a test point temperature value that represents the maximum

process temperature (for example, 140 °F or 60 °C). Select the

Upper Sensor Trim

button under the

Process Temperature Sensor Trim

heading and follow the on-screen prompts.

Recall factory trim

The

Recall Factory Trim

button will restore the transmitter to the original factory calibration settings.

When the recall factory trim function is used, the transmitter’s upper and lower trim values are set to the
values configured at the factory. If custom trim values were specified when the transmitter was ordered,
the device will recall those values. If custom trim values were not specified, the device will recall the
upper and lower sensor limits.

Transmitter RTD sensor matching using Callendar-Van Dusen
constants

The Rosemount 3051SMV accepts Callendar-Van Dusen constants from a calibrated RTD schedule and
generates a special custom curve to match that specific sensor Resistance vs. Temperature performance.
Matching the specific sensor curve with the transmitter configuration enhances the temperature
measurement accuracy.

«
...
100
101
102
103
104
...
»

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

Бренд: VeEX Страницы: 2

Бренд: DayTronic Страницы: 54

Бренд: Bacharach Страницы: 2

Бренд: Bachmann Страницы: 33

Бренд: C-LOGIC Страницы: 4

Бренд: C-lock Страницы: 32

Бренд: C-LOGIC Страницы: 12

Ultraprobe 9000

Бренд: UE Systems Страницы: 25

ULTRAPROBE 10000

Бренд: UE Systems Страницы: 6

Бренд: Veeder-Root Страницы: 59

Бренд: TSI Instruments Страницы: 4

Бренд: Zensol Страницы: 12

Бренд: ENSONIQ Страницы: 260

Бренд: mru Страницы: 32

Бренд: Liquivision Страницы: 84

IMI Sensors 66162APZ1

Бренд: PCB Piezotronics Страницы: 7

VideoScope Plus

Бренд: LaserLiner Страницы: 84

CellaTemp PK Series

Бренд: Keller Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды