manualshive.com logo in svg

Rosemount 3051S Series, Справочное руководство

Серия продукции Rosemount 3051S - это надежные и высокоточные датчики давления для широкого спектра применений. Для получения дополнительной информации по использованию устройства рекомендуется загрузить бесплатный Руководство по эксплуатации с официального сайта производителя. manualshive.com - ваш источник необходимых инструкций.

Поделиться
Скачать
background image

121

Reference Manual 

00809-0100-4803, Rev GA

Safety Instrumented Systems Requirements

September 2017

Safety Instrumented Systems Requirements

6.5

Rosemount 3051SMV SIS operation and maintenance

6.5.1

Proof test

The following proof tests are recommended. 
All proof test procedures must be carried out by qualified personnel. 

Use 

“Field Communicator Fast Keys” on page 62

 

to perform a loop test, analog output trim, or sensor 

trim. security switch should be in the (

) position during proof test execution and repositioned in the 

(

) position after execution.

6.5.2

Partial proof test

The partial suggested proof test consists of a power cycle plus reasonability checks of the transmitter 
output. This test will detect 

~

48% of possible DU failures in the device.

FMEDA report can be found at 

Emerson.com/Automation-Solutions/Pressure/Rosemount-3051SMV

 

and look at the certificates and approvals documentation.

Required tools: Field Communicator and mA meter.

1. Bypass the safety function and take appropriate action to avoid a false trip. 

2. Use HART communications to retrieve any diagnostics and take appropriate action.

3. Send a HART command to the transmitter to go to the high alarm current output and verify that the 

analog current reaches that value

.

(1)

 

See 

“Alarm level verification” on page 30

. 

4. Send a HART command to the transmitter to go to the low alarm current output and verify that the 

analog current reaches that value.

(2)

5. Perform a “reasonability check” on the pressure sensor reading and the sensor temperature reading 

and if applicable the process temperature reading.

(3)

6. Remove the bypass and otherwise restore the normal operation.

7. Place the Security switch in the (

) position.

6.5.3

Comprehensive proof test

The comprehensive proof test consists of performing the same steps as the simple suggested proof test 
but with a two point calibration of the pressure and temperature sensors in place of the reasonability 
check of the sensors. This test will detect 

~

90% of possible DU failures in the device.

Required tools: Field Communicator and pressure calibration equipment.

1. Bypass the safety function and take appropriate action to avoid a false trip.

2. Use HART communications to retrieve any diagnostics and take appropriate action.

3. Send a HART command to the transmitter to go to the high alarm current output and verify that the 

analog current reaches that value.

(1)

 See 

“Alarm level verification” on page 30.

4. Send a HART command to the transmitter to go to the low alarm current output and verify that the 

analog current reaches that value.

(2)

1. 

This tests for compliance voltage problems such as a low loop power supply voltage or increased wiring resistance. This also tests for other possible 
failures.

2. 

This tests for possible quiescent current related failures.

3. 

This tests for faults in the input multiplexer and A to D converter.

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

Magnetic Instrumentation 2130 Instruction Manual preview
2130
Бренд: Magnetic Instrumentation Страницы: 63
Kamstrup MULTICAL 62 Technical Description preview
MULTICAL 62
Бренд: Kamstrup Страницы: 100
Kamstrup MULTICAL 41 Installation And User Manual preview
MULTICAL 41
Бренд: Kamstrup Страницы: 16
Kamstrup MULTICAL 41 Installation Manual preview
MULTICAL 41
Бренд: Kamstrup Страницы: 12
Kamstrup flowIQ 3100 Technical Description preview
flowIQ 3100
Бренд: Kamstrup Страницы: 60
Kamstrup MULTICAL 403 Technical Description preview
MULTICAL 403
Бренд: Kamstrup Страницы: 136
Kamstrup ULTRAFLOW 54 Installation Manual preview
ULTRAFLOW 54
Бренд: Kamstrup Страницы: 16
Kamstrup MULTICAL 603 Technical Description preview
MULTICAL 603
Бренд: Kamstrup Страницы: 155
Olympus EPOCH 650 User Manual preview
EPOCH 650
Бренд: Olympus Страницы: 362
Olympus 27MG Getting Started Manual preview
27MG
Бренд: Olympus Страницы: 8
R&S FSMR3000 User Manual preview
FSMR3000
Бренд: R&S Страницы: 733
R&S ZNH User Manual preview
ZNH
Бренд: R&S Страницы: 369
Hama TH-300 Operating Instructions Manual preview
TH-300
Бренд: Hama Страницы: 16
Gas Data GFM 436 User Manual preview
GFM 436
Бренд: Gas Data Страницы: 99
Heyuan Intelligence DZ81-MA3UI5C User Manual preview
DZ81-MA3UI5C
Бренд: Heyuan Intelligence Страницы: 14
Fluke 1623-2 Quick Reference Manual preview
1623-2
Бренд: Fluke Страницы: 2
YOKOGAWA UPM101 User Manual preview
UPM101
Бренд: YOKOGAWA Страницы: 12
LaserLine QUAD 1000HDD Owner'S Manual preview
QUAD 1000HDD
Бренд: LaserLine Страницы: 11

Бренды по названию

Популярные бренды

Загрузить еще бренды