manualshive.com logo in svg

Rosemount 3051S Series, Справочное руководство

Поделиться
Скачать
Rosemount 3051S Series Скачать руководство пользователя страница 140

Specifications and Reference Data

September 2017

Reference Manual 

00809-0100-4803, Rev GA

Specifications and Reference Data

132

Temperature limits

Humidity limits

0–100 percent relative humidity

Turn-on time

Performance within specifications less than five seconds for 
Rosemount 3051SMV (typical) after power is applied to the 
transmitter.

Volumetric displacement

Less than 0.005 in

3

 (0,08 cm

3

)

Damping

Analog output response to a step change is user-selectable 
from 0 to 60 seconds for one time constant. Each variable 
can be individually adjusted. This software damping is in 
addition to sensor module response time.

Failure mode alarm

If self-diagnostics detect a gross transmitter failure, the 
analog signal will be driven offscale to alert the user. 
Rosemount standard (default), NAMUR, and custom alarm 
levels are available (see 

Table A-4

).

High or low alarm signal is software-selectable or 
hardware-selectable via the optional switch (option D1). 

A.1.3  Physical specifications

Electrical connections

1

/

2

–14 NPT, G

1

/

2

, and M20 

⫻

 1.5 (CM20) conduit. HART 

interface connections fixed to terminal block.

Process connections

1

/

4

–18 NPT on 2

1

/

8

-in. centers

1

/

2

–14 NPT and RC 

1

/

2

 on 2-in.(50.8 mm), 

2

1

/

8

-in. (54.0 mm), or 2

1

/

4

-in. (57.2 mm) centers (process 

adapters)

Ambient

–40 to 185 °F (–40 to 85 °C)

with LCD display

 

(1)

: –40 to 175 °F (–40 to 80 °C)

with option code P0: –20 to 185 °F (–29 to 85 °C)

1. 

CD display may not be readable and LCD display updates will be slower at 
temperatures below –4 °F (–20 °C).

Storage

–50 to 185 °F (–46 to 85 °C)

with LCD display: –40 to 185 °F (–40 to 85 °C)

with wireless output: –40 to 185 °F (–40 to 85 °C)

Process temperature limits

At atmospheric pressures and above:

Silicone fill sensor

(2)(3)

2. 

Process temperatures above 185 °F (85 °C) require derating the ambient 
limits by a 1.5:1 ratio. For example, for process temperature of 195 °F 
(91 °C), new ambient temperature limit is equal to 170 °F (77 °C). This can be 
determined as follows: 
(195 °F –185 °F) 

⫻

 1.5 = 15 °F,

185 °F–15 °F = 170 °F

3. 

212 °F (100 °C) is the upper process temperature limit for DP Range 0.

with coplanar flange

–

40 to 250 °F (

–

40 to 121 °C)

(4)

4. 

220 °F (104 °C) limit in vacuum service; 130 °F (54 °C) for pressures below 0.5 
psia.

with traditional flange

–

40 to 300 °F (

–

40 to 149 °C)

(4)(5)

5. 

–20 °F (–29 °C) is the lower process temperature limit with option code P0.

with level flange

–

40 to 300 °F (

–

40 to 149 °C)

(4)

with Rosemount 305 
Integral Manifold

–

40 to 300 °F (

–

40 to 149 °C)

(4)(5)

Inert fill sensor

(2)

(6)

6. 

32 °F (0 °C) is the lower process temperature limit for DP Range 0.

–

40 to 185 °F (

–

40 to 85 °C)

(7)

7. 

For Rosemount 3051SMV_ _ 1, 2, 140 ° F (60 °C) limit in vacuum service.

Table A-4.  Alarm Configuration

High alarm

Low alarm

Default

≥ 

21.75 mA

≤ 

3.75 mA

NAMUR compliant

(1)

1. 

Analog output levels are compliant with NAMUR recommendation NE 43, 
see option codes C4 or C5.

≥ 

22.5 mA

≤ 

3.6 mA

Custom levels

(2)

2. 

Low alarm must be 0.1 mA less than low saturation and high alarm must be 
0.1 mA greater than high saturation.

20.2–23.0 mA

3.6–3.8 mA

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды