Rosemount 3051S Series Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 190

background image

67

Reference Manual

00809-0100-4803, Rev GA

Installation

September 2017

Installation

3.3

Installation considerations

3.3.1

General

Measurement performance depends upon proper installation of the transmitter, impulse piping, and
process temperature sensor. Mount the transmitter close to the process and use minimum piping to
achieve best performance. Also, consider the need for easy access, personnel safety, practical field
calibration, and a suitable transmitter environment. Install the transmitter to minimize vibration, shock,
and temperature fluctuation.

Note

Install the enclosed pipe plug (found in the box) in the unused conduit opening if optional process
temperature input is not used. For proper straight and tapered thread engagement requirements, see
the appropriate approvals drawings in

Appendix B: Product Certifications

For material compatibility considerations, see Material Selection

3.3.2

Mechanical

For steam service or for applications with process temperatures greater than the limits of the
transmitter, do not blow down impulse piping through the transmitter. Flush lines with the blocking
valves closed and refill lines with water before resuming measurement.

When the transmitter is mounted on its side, position the coplanar flange to ensure proper venting or
draining. Mount the flange as shown in

Figure 3-5 on page 72

, keeping drain/vent connections on the

bottom for gas service and on the top for liquid service.

3.3.3

Environmental

Access requirements and

“Cover installation” on page 69

can help optimize transmitter performance.

Mount the transmitter to minimize ambient temperature changes, vibration, mechanical shock, and to
avoid external contact with corrosive materials.

“Specifications and Reference Data” on page 125

temperature operating limits.

3.4

Installation procedures

3.4.1

Configure security (write protect)

Changes to the transmitter configuration data can be prevented with the security (write protect) switch
located on the feature board. See

Figure 3-1 on page 68

for the location of the switch. Position the

switch in the

ON

position to prevent accidental or deliberate change of configuration data.

If the transmitter write protection switch is in the

ON

position, the transmitter will not accept any

“writes” to its memory. Configuration changes, such as digital trim and reranging, cannot take place
when the transmitter security is on.

To reposition the switches, follow the procedure described below:

1. Do not remove the transmitter covers in explosive atmospheres when the circuit is live. If the

transmitter is live, set the loop to manual and remove power.

2. Remove the housing cover opposite the field terminal side of the housing.

3. To reposition the switches as desired, slide the security and alarm switches into the preferred position

using a small screwdriver. See

Figure 3-1 on page 68

.

«
...
73
74
75
76
77
...
»

Содержание 3051S Series































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 3051S Series

Бренд: Yamaha Страницы: 69

Бренд: Aaronia Страницы: 47

Бренд: J.P. Instruments Страницы: 9

Бренд: J.ASSY Страницы: 13

Бренд: Keysight Страницы: 66

Бренд: Tektronix Страницы: 20

Бренд: TA Instruments Страницы: 68

Бренд: Hanna Instruments Страницы: 28

Бренд: Konica Minolta Страницы: 92

Бренд: Omega Страницы: 16

Бренд: A&D Страницы: 10

Бренд: Keithley Страницы: 338

Mini HD Recorder

Бренд: Green Feathers Страницы: 8

Бренд: Smartwares Страницы: 2

DUSTHUNTER SB30

Бренд: SICK Страницы: 72

Бренд: Micro-g LaCoste Страницы: 168

Бренд: Fluke Страницы: 14

Бренд: Keysight Страницы: 41

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды