manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 6

SECTION 1 — IN GENERAL

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

6

 

Call: 1-800-922-7533

(Continued on next page.)   

Accompanying this equipment is an 8-1/2” x 
11” operator safety precaution pamphlet, Part 
No. KSC-000, for anyone operating the machine 
where this equipment will be installed. This 
precaution pamphlet is to be given to all oper-
ators, including setup people, maintenance 
personnel and supervisors.

This pamphlet should also be attached to the 
machine, readily accessible and visible to the 
operator. (A hole in the corner of this precau-
tion pamphlet is provided for attaching pur-
poses.)  Additional copies of this precaution 
are available. Please call, e-mail, write, fax, 
or use the order form found on a later page in 
this manual.

When a language barrier or insufficient edu-
cation prevents a person from reading or 
understanding the contents of this operator 
safety precaution pamphlet, you should either 
translate this information or have it read or 
interpreted to the person. Make sure that the 
person understands the information.  To order 
this pamphlet in Spanish, use Part No. KSC-
000S; in French, use Part No. KSC-000F.

This precaution pamphlet must be reviewed daily.

Operator Safety Precaution Pamphlet - 

(Attachment for machine operators)

Part No. KSC-000

Part No. KSC-000

Front

Back

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды