manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 37

SECTION 7 — FAULT MESSAGES   

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC
Call: 1-800-922-7533  

37

(Continued on next page.)   

FATAL FAULT MESSAGES FOR SSC-500

Table 7.1 

(continued)

GENERAL FAULT MESSAGES FOR SSC-500

GENERAL fault messages can be cleared by touching 

ENTER

 on the keypad/display.

Table 7.2

MESSAGE

CAUSE

ACTION TO TAKE

KEYPAD FLT

KEYPAD failure.

Check for correct wiring to the keypad and terminals.

RUN/INCH PB FLT

RUN/INCH palm button failure.

Check for correct wiring to the palm buttons and terminals.

FOOT SW FLT

FOOT SWITCH failure.

Check for correct wiring to the foot switch and terminals.

BOS LIMIT SW FLT

The Bottom Of Stroke Limit Switch is stuck ON or OFF.

Check the status LED on the BOS limit switch input. Check all 
wiring to the switch. Check 24 VDC power supply.

TOS LIMIT SW FLT

The Top Of Stroke Limit Switch is stuck ON or OFF.

Check the status LED on the TOS limit switch input. Check all 
wiring to the switch. Check 24 VDC power supply.

TOS TIMEOUT FLT

The Top Of Stroke Limit Switch did not come ON within 
10 seconds of the UP solenoid valve coming on.

Check the status LED on the TOS limit switch input. Check 
all wiring to the switch. Check 24 VDC power supply.  Make 
sure the UP solenoid valve is energizing and that there is 
hydraulic system pressure.

TONNAGE P.S. FLT

The Tonnage Pressure Switch is stuck ON.

Check the status LED on the tonnage pressure switch input. 
Check all wiring to the switch. Check 24 VDC power supply.

AUX CPU FLT

CPU #2 fault.

Internal circuitry failure, consult factory.

MESSAGE

CAUSE/SOLUTION

HAND OR FOOT ONLY

The initiating means is in the HAND/FOOT mode. This selection is only allowed in the Sequence-Stop Mode. Set 
selector to HAND or FOOT, or change selector to SINGLE.

NO INTERLOCKS

The selected operation requires different interlocks to function. The required interlocks are not currently available. (See 
interlock information on page 11.)

RETURN RAM

The ram is not at TOS (Top of Stroke). Press any palm button to return the ram  to TOS.

PRESET REACHED

The BATCH PRESET count was reached. Press ENTER to clear both the message and the batch counter.

PSDI REQUIRES LC

The light curtain is turned off or is red when PSDI is enable. Check the status of the light curtain and make sure it 
is turned on. The message will clear when the light curtain is on.

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды