manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 36

SECTION 7 — FAULT MESSAGES

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

36

 

Call: 1-800-922-7533

(Continued on next page.)   

FATAL FAULT MESSAGES FOR SSC-500

FATAL fault messages can NOT be cleared. An E-STOP is required for the press brake to recover. The problem should be fixed and then power 
restored to the machine.

CPU = Central Processing Unit
LED = Light Emitting Diode
SSR = Solid State Relay
F = Fuse

Table 7.1

MESSAGE

CAUSE

ACTION TO TAKE

NV-RAM FLT

CPU #1 had trouble reading or writing the nonvolatile 
(NV) RAM memory and could not repair the data. The 
battery socket or RAM chip could be inoperative.

Turn the main power off and back on. All 
variables are reset to factory default and will 
need to be reprogrammed. Contact factory for 
technical support.

SSR #1, K1 ON FLT

The processor did inot detect, through feedback, 
that the SSR #1 (Solid State Relay) turned ON, or 
that K1 relay contacts did not turn ON after K1 was 
energized.

Check SSR#1 output fuse (F2). Check K1 output 
LED. Make sure the K1 relay is energizing. One 
or more components may be defective. Contact 
factory for technical support.

SSR #1, K1 OFF FLT

The processor did inot detect, through feedback, 
that the SSR #1 (Solid State Relay) turned OFF, or 
that K1 relay contacts did not turn OFF after K1 was 
deenergized.

Check SSR#1 output fuse (F2). Check K1 output 
LED. Make sure the K1 relay is deenergizing. 
One or more components may be defective. 
Contact factory for technical support.

SSR #2 ON FLT

he processor did inot detect, through feedback, that 
the SSR #2 (Solid State Relay) turned ON.

Check SSR#2 output fuse (F2). One or more 
components may be defective. Contact factory 
for technical support.

SSR #2 OFF FLT

The processor did inot detect, through feedback, 
that the SSR #2 (Solid State Relay) turned OFF.

Check SSR#2 output fuse (F2). One or more 
components may be defective. Contact factory 
for technical support.

VALVE SW ON FLT 
(FOR HYDRAULIC 
BLOCK VALVE 
MONITOR)

The block valve monitoring switch did not turn ON.

Check the state of the controls on the block 
valve monitoring switch. Contact factory for 
technical support.

VALVE SW OFF FLT 
(FOR HYDRAULIC 
BLOCK VALVE 
MONITOR)

The block valve monitoring switch did not turn OFF.

Check the state of the controls on the block 
valve monitoring switch. Contact factory for 
technical support.

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды