Rockford Fosgate SSC-500 Скачать руководство пользователя страница 26

Страница: 26 / 44

SECTION 4 — PROGRAMMING

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

Call: 1-800-922-7533

(Continued on next page.)

CLEAR STROKE

UP ARROW CONFIRM

Selects the Program Menu

Item CLEAR STROKE

ENTER

Display now reads...

MAIN

ENTER

Press the UP arrow to

confirm the clear or enter

to abort

CLEAR STROKE

Select the

PROG

position on the Program/Run selector switch.

Press the

and

buttons on the keypad to scroll through the

program options. Press

ENTER

when the LCD displays

CLEAR STROKE

The display now reads:

UP ARROW CONFIRM

Press the

button on the keypad to clear the stroke counter, or press

the

ENTER

button to abort the clear and return to the main menu level.

The LCD again displays

CLEAR STROKE

Function

The 7-digit stroke counter is used to count strokes in the single or
automatic modes of operation only and can be displayed when the
Program/Run selector switch is in the

RUN

position.

Figure 4.4
CLEAR STROKE Programming Flowchart

QUICK REFERENCE TABLE - FACTORY SETTINGS AND VALID RANGES Table 4.1

Program Setting

Valid Entry Range

Factory Preset Setting

Clear Stroke

Clear/Abort

Clear batch

Clear/Abort

Batch Preset

0000000 - 9999999

0000000

Bottom dwell ms

0 - 3000 ms

Decompress timer

25 - 250 ms

Anti-Tiedown timer

100 - 7000 ms

250 ms

Single Return Mode

Off/On

Off

PSDI Timer

002 - 30 sec.

002 sec

Automatic single stroke mode

Off/On

Off

Auto single timer

005 - 120 sec. ms

005 sec.

User inputs

Input #1 - #4

Lube Flt/Off/E-Stop

Содержание SSC-500













































Результаты поиска

Содержание SSC-500

Отзывы:

Бренды по названию

Популярные бренды

Rockford Fosgate SSC-500, Руководство по установке

Результаты поиска

Содержание SSC-500

Отзывы:

Бренды по названию

Популярные бренды