manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 17

SECTION 3 — INSTALLATION OF COMPONENTS 

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC
Call: 1-800-922-7533  

17

(Continued on next page.)   

The keypad/display assembly (shown here) is used to enter setup 
information and to monitor machine operation. 
The keypad/display can be furnished in a remote enclosure up to a 
maximum of 150’ from the SSC-500 control module. Display mode 
choices during the machine run cycle are MODE-STATUS, STROKE 
COUNTER, or BATCH COUNTER. All programming is accessed by a keyed 
selector switch on the keypad/display unit.
If the keypad/display is supplied in a remote enclosure, please refer to 
the section on wiring (page 23) and the electrical schematic prints that 
came with the control box on the proper wiring connection.

Mounting the Control Box

Solidly mount the control box in an accessible location, either on or 
near the machine to be controlled. A convenient location will keep 
conduit runs to a minimum length.
Although operation of this control will not be adversely affected by 
normal machine operation, excessive shock or vibration may require 
shock mounting in specific applications.

The key must be removed from the off/run/
program selector switch after the control is 
programmed and before the machine is released 
to production. All keys must be supervisory 
controlled at all times. 

Photo 3.5
Operator Interface Keypad/Display

The only user serviceable parts on the “dual CPU” board are the EPROM and fuses F1 - F5. If any changes to the circuit boards are required, 
instructions will be sent with the new parts. See page 39 for instructions on replacing the EPROM.

Control Module Assembly 

(continued)

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды