manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 24

SECTION 3 — INSTALLATION OF COMPONENTS

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

24

 

Call: 1-800-922-7533

(Continued on next page.)   

Do not operate the press if the ground indicator light does not illuminate when the station is turned on.

Press Ground

The machine frame must always be firmly connected to ground in order to ensure that the control potential will never exceed 120 volts above ground. 
Run a green grounding wire from the control box to some convenient location directly on the machine frame. Connect one end solidly to the frame 
using a mounting bolt or other convenient means of attachment. Scrape any paint, rust, etc., from the area, to ensure an adequate ground connection. 
Connect the other end to the “GND” terminal in the control box.

Note:  All exposed metal components, which may be touched by personnel during normal operation or adjustment, must be firmly grounded to the 

machine frame. The disconnect switch and motor starter should also be grounded if they are mounted separately.

Setup of Control System

The flowchart in Figure 4.1 outlines the order and method of setting up 
and programming the SSC-500  control system on a hydraulic press 
after installation. Refer to the LCD display on the control box or remote 
operator station.

Power Up Control

Program User

Inputs

Program Standard

Settings

Ready for

Production

See Pages 29 - 30

 Step

Completed

Step

See Pages 26 - 29

See Page 24

Program Additional

Settings

See Pages 30 - 33

Figure 4.1
Initial Setup Procedure Flowchart

Initial Setup Procedure

After completing the installation of the control box and control com-

ponents, the SSC-500 control system must be initially programmed in 

order to get the machine up and running. To do this, please follow the 

Initial Setup Procedure

 below.

1.

   Turn the main power disconnect switch for the control to the 

ON position and start the main motor. The following information is 

displayed on the LCD:

VERSION X.0 

(X.0 = current keypad/display firmware version)

gg 

SHC - X.0

 gg

OPTION XX

(XX = current options available)

SAFEGRD IN PLACE

2.

   After this information is displayed, press 

ENTER

 on the keypad if the 

answer is 

YES

 to the 

SAFEGRD IN PLACE

 question.

3. 

 

READY TO START (Press Motor Start)

   The display message will indicate the position of the Program/Run 

selector switch as follows:

   If the selector switch is in the OFF position, the display message is 

OFF

.

   If the selector switch is in the RUN position, the display message is 

SINGLE - STOP

   If the selector switch is in the PROG position, the display message 

is 

CLEAR STROKE

.

4.  

Proceed to the 

Programming Overview

 on page 25.

Figure 4.2 - Initial Information on Display

SECTION 4—PROGRAMMING

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды