manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 18

SECTION 3 — INSTALLATION OF COMPONENTS

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC

18

 

Call: 1-800-922-7533

(Continued on next page.)   

PART NO. CTL-525 - PALM BUTTON ASSEMBLY 

(If furnished, see Installation Manual No. KSL-071 or KSL-073)

When the standard modes of operation of off, inch, single stroke, automatic, and auto single are furnished, the palm button assembly will consist 
of four buttons (two run/inch buttons with ring guards, one red emergency-stop button, and one yellow return/inch-up button). Along with these 
buttons will be four mounting boxes (three double hub and one single hub). Optionally available are the Touchdown™ or chrome “light push” palm 
buttons. These may be furnished in place of the standard black run/inch palm buttons. The palm buttons can be assembled as shown in Photo 3.7 
and mounted according to the requirements of the application. Nipples for connecting and running wire are not furnished.

Install the palm “run” buttons in such a way that it requires the use of both hands to cycle the machine.

Note: These operator controls are furnished when  
the “automatic” mode of operation is provided.

Black Run/Inch Button

Black Run/Inch Button

Red Emergency-Stop 

Button

Yellow Return/Inch-Up Button

Prior-Action Push Button

Photo 3.7

Photo 3.6
Back Side of Keypad/Display

Off/Run/Program 

Selector Switch

Keypad/Display CPU

Connector P5

Contrast 

Adjustment R2

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды