manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 39

SECTION 8 — MAINTENANCE AND INSPECTION   

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC
Call: 1-800-922-7533  

39

(Continued on next page.)   

The maintenance and inspection sections in this manual cannot be all-inclusive. Always refer to the original 
equipment manufacturer’s maintenance manuals or the machine owner’s manual. If you do not have an 
owner’s manual, contact the machine manufacturer.

Care of Keypad/Display

To clean the keypad/display, use a clean soft cloth with soap and warm water. Do not use oily rags, solvents, or ammonia-based glass cleaner.

Replacement of the “U4” EPROM

1.

   Shut off power to the main motor. Turn the main disconnect switch to the OFF position and lock it out. Open the door of the control enclosure. 

Remove the eight screws on the cover of the SSC-500 Control Module (See Photo 3.3 on page 16). When they are removed, pull the cover 
straight off over the relays and transformers. 

2.

   Locate the “U4” main EPROM (see Photo 3.4 on page 16 and Photo 8.1 below). It is located below the K2 Solenoid Relay on the “dual CPU” 

(Control Processing Unit) board.

 

3.

   Carefully remove the existing EPROM by pulling it straight out of the socket. Be careful not to bend the legs. Set aside the EPROM that was removed.

4.

   Prior to inserting the new EPROM, match the small notch in the top of the EPROM to the notch in the socket. Verify that the notch in the EPROM 

and the socket are lined up. Very carefully insert the new “U4” EPROM into the socket. Be careful not to bend any legs on the EPROM while 
pushing it into the socket. Make sure all the legs on the EPROM are properly seated into the socket. The legs must not be bent under or over 
the socket.

5.

   Replace the cover and the screws on the SSC-500 Control Module. Close the control enclosure door.

6.

   Turn the disconnect switch to the ON position. The 

Initial Setup Procedure

 must be completed before proceeding. Please see page 24 of this manual.

“U4” EPROM

Photo 8.1

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды