manualshive.com logo in svg

Rockford Fosgate SSC-500, Руководство по установке

Поделиться
Скачать
Rockford Fosgate SSC-500 Скачать руководство пользователя страница 33

SECTION 4 — PROGRAMMING  

SSC-500 Hydraulic Press Solid-State Control

Rockford Systems, LLC
Call: 1-800-922-7533  

33

(Continued on next page.)   

Figure 4.16
OPTIONS EDIT Flowchart

OPTIONS EDIT

The optional modes that can be configured using the options menu 
are—

TOS LS LOGIC (N.O./N.C.), BOS LS LOGIC (N.O./N.C.),

 

FOOT 

TRIP (OFF/ON), SC SOL ON (SLOW/FAST), SC LS (N.O./N.C.), HI 
ON BOS (OFF/ON), AND VALVE LS (N.O./N.C.). 
OPTIONS EDIT

Turn the main power disconnect switch off. Select the 

OFF

 position on 

the 

PROG/RUN

 key selector switch. Push and hold the 

ENTER

 button 

on the keypad and turn the main power disconnect switch 

ON

. Hold 

the 

ENTER

 button until the display switch reads back 

OPTIONS EDIT

. 

Release the 

ENTER

 button.

The display now reads: 

TOS LS N.O.

Press the 

ENTER

 key to toggle between

 N.O. 

and 

N.C.

 

Press the 

t

 and 

s

 buttons to scroll to the next option. 

The display now reads: 

BOS LS N.O.

Press the 

ENTER

 key to toggle between

 N.O. 

and 

N.C.

 

Press the 

t

 and 

s

 buttons to scroll to the next option. 

The display now reads: 

FOOT TRIP OFF

Press the 

ENTER

 key to toggle between

 OFF 

and 

ON

. 

Press the 

t

 and 

s

 buttons to scroll to the next option. 

The display now reads: 

SC SOL ON=SLOW

Press the 

ENTER

 key to toggle between

 SLOW 

and 

FAST.

Press the 

t

 and 

s

 buttons to scroll to the next option.

The display now reads: 

SC LS N.O.

Press the 

ENTER

 key to toggle between

 N.O. 

and 

N.C.

Press the 

t

 and 

s

 buttons to scroll to the next option. 

The display now reads: 

HI ON BOS=OFF

Press the 

ENTER

 key to toggle between

 OFF 

and 

ON

. 

Press the 

t

 and 

s

 buttons to scroll to the next option. 

The display now reads: 

VALVE LS N.O. 

Press the 

ENTER

 key to toggle between

 N.O. 

and 

N.C.

After the correct information has been entered, select the 

RUN 

position 

on the 

PROG/RUN

 key selector switch.

Содержание SSC-500













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды