RiTTO TWINBUS Скачать руководство пользователя страница 103

Страница: 103 / 197

Installation: Assembly, connection and start-up

103

tio

2.7.3 TwinBus switching device 1 4981

Assembly

Remove the TwinBus device and the supplied components from the packaging.

Connection

* Optional, customer-installed push button

** Light button on button module

Circuit diagram:

switching device with power supply unit, switches consumer up to 230 V, 6 A.

Note:

Programming mode must be set in order to connect the main door station to an indoor telephone
within the floor line. You

must

switch to normal mode after programming.

The floor door station bell buttons are assigned in normal mode.

When programming main door bell buttons on floor line indoor telephones, the floor control unit
1 4585 must first be switched to programming mode, then the indoor telephones and indoor video
stations must be programmed.

* Cut off the cover for connecting to additional devices.

Connections

a, b

Connection to TwinBus

LT+, LT-

Control input, e. g. for bell buttons

S, M, Ö

Relay output (230 V changeover contact)

System bus

for supplying additional devices from power supply unit 1 7573

00128-0

a b

LT+

LTÐ

3 *

00129-0

RiTTO

Содержание TWINBUS






































































































































































































Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды

RiTTO TWINBUS, Системное руководство

Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды