RiTTO TWINBUS Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 197

background image

Installation: Assembly, connection and start-up

51

In

st

al

la

tio

n

Two-man start-up

If the time limit has been exceeded:

Repeat the procedure.

If the programming procedure failed:

The memory of the indoor video station is full when 10 bell buttons have already been programmed. If necessary,
delete all settings and reprogram the pushbutton that is needed.

Start-up using the apartment button

If the time limit has been exceeded:

Repeat the procedure.

If the programming procedure failed:

Check on the TwinBus power supply unit whether the setting protection is activated - see page

.

Activity

Result

✔

Short tone: Device is ready for operation.

/

No tone: Time limit exceeded.

/

Long tone: Programming procedure failed.

Activity

Result

✔

Short tone: Device is ready for operation.

/

No tone: Time limit exceeded.

/

Long tone: Programming procedure failed.

>Press and hold for 5 s
until

flashes

RiTTO

announce button to be assigned via
speech connection

RiTTO

Within one minute, press the button to
be assigned on the door station

acoustic signal for confirmation at
indoor video station and door station

RiTTO

Open plexiglass cover on power supply unit
1 7573

Press and hold "P" until

LD 1 (yellow)
flashes

LED 2 (red)
flashes,

LD1 goes out

Within three minutes, go to the apartment
button. Press and hold it for 5 s

acoustic signal for confirmation at
indoor video station

Within one minute, press the button to be
assigned on the door station

RiTTO

RiTTO

acoustic signal for confirmation
at indoor telephone and indoor
video station

«
...
49
50
51
52
53
...
»

Содержание TWINBUS






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TWINBUS

Бренд: ICP DAS USA Страницы: 6

Бренд: Dahua Страницы: 15

Бренд: Peavey Страницы: 4

Бренд: Farfisa Страницы: 24

ProMedia Ultra 2.0

Бренд: Klipsch Страницы: 7

Бренд: Medion Страницы: 308

Бренд: MAG Страницы: 20

Бренд: M-system Страницы: 8

Бренд: Alto Страницы: 40

SKY PRO 10 CPC 58

Бренд: KU Solar Страницы: 50

Бренд: FAAC Страницы: 16

Бренд: Onkyo Страницы: 4

Бренд: Commax Страницы: 15

Бренд: Valcom Страницы: 4

Self-Powered Loudspeaker Systems USM-P Series

Бренд: Meyer Sound Страницы: 12

Бренд: Alphatec Страницы: 2

Бренд: auna multimedia Страницы: 26

Бренд: Edirol Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды