RiTTO TWINBUS Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 197

background image

General Information

11

General Information

1.4

The video system

Installation requirements for video cameras

A camera can only view a certain area. In order for the visitor who has just rung to be monitored, for example, the
camera must be appropriately installed.

The surveillance area varies according to the angle the camera module is set.

The installation height is approx. 1.5 to 1.6 m.

The area surveilled must be well illuminated, also at night. If necessary, appropriate lighting must also be installed.

We recommend positioning an external light about 1 m above the camera. It should be an incandescent bulb of
at least 40 W.

The camera must not be pointed towards the source of light (sun, lighting, reflection, etc.).

Terminal resistor

Circuit diagram:

terminal resistor for mixed systems.

A

indoor video station as the last device in the line

*

Terminal resistor: ON

B

indoor video station as the last device in the line

** Terminal resistor: OFF

Note:

You must switch on the terminal resistor if the indoor video station 1 7857 or 1 7855 or handsfree
video intercom unit 1 7835 or 1 7845 you want to install is the last device in the video bus line.
If the last device installed in the video bus line is an indoor video station 1 7815 or 1 7825, manually
use a 100

Ω

resistor 1 7832.

Caution!

Reduced image quality

Incorrectly set terminal resistors will lead to reduced image quality.

1 7857

1 7857

Va Vb

Va Vb

Va Vb

))

*

Va Vb

Va Vb

Va Vb

1 7815/25

1 7815/25

S0121-0

«
...
9
10
11
12
13
...
»

Содержание TWINBUS






































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TWINBUS

Бренд: FAAC Страницы: 36

Бренд: Dahua Страницы: 23

VTO2000A Series

Бренд: Dahua Страницы: 41

Бренд: Dahua Страницы: 85

Бренд: Jensen Страницы: 2

Бренд: Q Acoustics Страницы: 19

Бренд: WAFER Страницы: 13

kb sound Series

Бренд: EIS Страницы: 2

Бренд: TCS Страницы: 30

NEOS DIGITAL KVD-2 S1 COAX

Бренд: Auta Страницы: 4

Бренд: Rain Страницы: 58

Бренд: Racal Instruments Страницы: 110

Бренд: Teac Страницы: 38

Бренд: chinavasion Страницы: 7

Бренд: M-system Страницы: 3

I/O-SYSTEM 750-610

Бренд: WAGO Страницы: 14

MOVIE CD 1500 - TEST NEWS

Бренд: Canton Страницы: 1

Бренд: Sensitron Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды