RiTTO TWINBUS Скачать руководство пользователя страница 60

Страница: 60 / 197

Inst

alla

tion

Installation: Assembly, connection and start-up

Concealed and cavity wall installation

A flush-mounted frame 1 7320 is required for installation. The flush-mounted frame is plastered in or attached using
the provided cavity wall clamps.

1. Cavity wall clamps
2. Fastening screws for cavity wall clamps
3. Plastering protection
h: 242 mm
b: 122 mm
t:

35 mm

Note:

The plaster protection (3) provides protection from soiling. It should only be removed just before
the handsfree intercom unit is installed.

If the walls are not plastered, the thickness of the plaster to be applied must be taken into
consideration during installation.

00034-0

120

8,5

00768-0

00769-0

Содержание TWINBUS






































































































































































































Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды

RiTTO TWINBUS, Системное руководство

Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды