RiTTO TWINBUS Скачать руководство пользователя страница 108

Страница: 108 / 197

Inst

alla

tion

Installation: Assembly, connection and start-up

108

Setting the operating mode

Door selector switch 1 4982 can operate in operating modes with or without the busy function.

The operating mode is set using a bridge between terminals AV and BV. The busy function operating mode is set with
a bridge.

Busy function: ON

An existing link between a door station and the system is maintained. The bell button cannot be operated from another
door station for approximately 25 seconds whilst the link exists.

2.7.5 TwinBus area coupler 1 4213

Assembly

Remove the TwinBus device and the supplied components from the packaging.

Please also follow the provided operating instructions.

Note:

If more than one door selector switch is used, line 41 must be connected across the joints.

* Cut off the cover for connecting to additional devices.

Connections

A, B

Bus

a, b

Main bus line

, V

Main video bus

TwinBus power supply unit, TwinBus

System bus

for supplying additional devices from power supply unit 1 7573

00368-0

00360-0

Содержание TWINBUS






































































































































































































Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды

RiTTO TWINBUS, Системное руководство

Результаты поиска

Содержание TWINBUS

Отзывы:

Похожие инструкции для TWINBUS

Бренды по названию

Популярные бренды