background image

R7G4FML3-6-DA16

P. 1 / 10

EM-7774-A Rev.2

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: +81(6)6659-8201   Fax: +81(6)6659-8510   E-mail: [email protected]

PNP/NPN DISCRETE INPUT MODULE

(16points, MECHATROLINK-

III

)

MODEL

R7G4FML3-6-DA16

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System.  Before use, please check 
contents of the package you received as outlined below.
If you have any problems or questions with the product, 
please contact M-System’s Sales Office or representatives.

The unit is for use in general industrial environments, 
therefore may not be suitable for applications which require   
higher level of safety (e.g. safety or accident prevention sys-
tems) or of reliability (e.g. vehicle control or combustion con-
trol systems).  
For safety, installation and maintenance of this unit must 
be conducted by qualified personnel.  

 PACKAGE INCLUDES:

  Discrete input module .................................................. (1)
  DIN rail mounter slider ............................................... (2)

 MODEL NO.

Confirm that the model number described on the product is 
exactly what you ordered.

 INSTRUCTION MANUAL

This manual describes necessary points of caution when 
you use this product, including installation, connection and 
basic maintenance procedures.

 SYMBOLS USED ON THE PRODUCT

Functional earth symbol is marked on terminal cover of 
Power Supply Terminals for UL.

POINTS OF CAUTION

 CAUTION

•  If  the  unit  is  not  used  in  a  manner  not  specified  by  M-

system, the protection provided by the equipment may be 
impaired.

 CONFORMITY WITH EU DIRECTIVES OR UL

• 

The actual installation environments such as panel con-

figurations, connected devices and connected wires may 
affect the protection level of this unit when it is integrated 
in a panel system.  The user may have to review the CE 
requirements in regard to the whole system and employ 
additional protective measures to ensure CE conformity.

• This unit is suitable for Pollution Degree 2.
• Altitude up to 2000 meters.
• The  power  supply  and  the  external  power  supply  must 

satisfy SELV requirements in accordance with the cur-
rently applicable safety standards. (SELV = Safty Extra 
Low Voltage).

•  Install  inside  an  industrial  control  panel  or  equivalent 

for UL.

 POWER INPUT RATING & OPERATIONAL RANGE

• Locate the power input rating marked on the product and 

confirm its operational range as indicated below:

  24V DC rating: 24V ±10%, approx. 75mA

 GENERAL PRECAUTIONS

• Before you remove the unit or mount it, turn off the power 

supply and input signal for safety.

• Before you remove the terminal block or mount it, turn off 

the power supply and input signal for safety.

 ENVIRONMENT

• Indoor use
• When  heavy  dust  or  metal  particles  are  present  in  the 

air, install the unit inside proper housing with sufficient 
ventilation.

• Do not install the unit where it is subjected to continuous 

vibration.  Do not subject the unit to physical impact.

• Environmental temperature must be within -10 to 55°C 

 

(14 to 131°F) with relative humidity within 30 to 90% RH 

in order to ensure adequate life span and operation.

 WIRING

•  Do  not  install  cables  close  to  noise  sources  (relay  drive 

cable, high frequency line, etc.).

•  Do  not  bind  these  cables  together  with  those  in  which 

noises are present.  Do not install them in the same duct.

• Be sure to close the terminal cover for safety.

 AND ....

• The unit is designed to function as soon as power is sup

-

plied, however, a warm up for 10 minutes is required for 

satisfying complete performance described in the data 
sheet.

Содержание R7G4FML3-6-DA16











Отзывы: