Riello Family PRO 42 IS Скачать руководство пользователя страница 20

Страница: 20 / 76

It is advisable to contact your local waterworks office (authority

responsible for waste water regulations) well before commencing

with the installation of the neutralizer kit in order to establish

details of local regulations that apply.

NOTICE

: to avoid a negative pressure onto the condensate check

valve, pipe ventilation must take place between the condensate

trap and the drainage system, in case of discharge into:

a public sewage system

a neutralizer kit

a condensate pump kit

7.5

General piping information

CAUTION:

Use two wrenches when tightening water piping

at the boiler, using one wrench to prevent the boiler return

line or supply line from turning. Failure to support the boiler

piping connections to prevent them from turning could

cause damage to boiler components.

NOTICE

: The Family PRO boiler control module uses temperature

sensors to provide both high limit protection and modulating

temperature control. The PCB also provides low water protection

using a water pressure sensor (minimum 6.5 psi (0.45 bar)). Some

codes/jurisdictions may require additional external controls for

high limit and/or low water cutoff protection.

7.5.1

Separate low water cutoff

A low water cutoff may be required by state local code or

some insurance companies. Check code requirements before

installation of the Family PRO boiler. If required:

− Use a low water cutoff designed for hydronic installations

− Follow low water cutoff manufacturer’s instructions

A hot water boiler installed above the radiation level or as

required by the Authority having jurisdiction, must be provided

with a low water cutoff device either as part of the boiler or at

the time of boiler installation.

Note: The electronic low water cutoff located internally in the

Family PRO 42 KIS-IS is below the lowest safe permissible water

level established by the boiler manufacturer.

7.5.2

ackflow

preventer (heating only model)

Use a backflow preventer specifically designed for hydronic

boiler installations. This valve should be installed on the

cold water fill supply line per local codes.

7.5.3

Fitting the heating circuit supply and

return pipes

NOTICE

: To protect the entire heating system

recommends

installing a Y-Strainer in the return circuit. When connecting the

boiler to an existing heating system this device must be installed.

− Install shut-off valves immediately before and after the

Y-Strainer to enable the Y-Strainer to be cleaned.

− Install a fill valve and drain valve in the heating system supply

pipe if required.

− Also plumb the pressure relief valve to the drain system.

NOTICE

: When using oxygen-permeable pipes, e. g. for floor

heating systems, you must separate the system using heat

exchangers.

− Thoroughly flush all pipes and radiators

− Refer to the installation wall template for the pipe connection

dimensions

− Connect the pipes so that they are free from strain.

7.5.4

Available Pump Head (ft. hd.)

Size the piping and components in the space heating system

using recognized design methods.

NOTICE

: The boiler, when used in connection with a refrigeration

system, must be installed so the chilled medium is piped in

parallel with the boiler and with appropriate valves to prevent

the chilled medium from entering the boiler.

NOTICE

: The boiler piping system of a hot water boiler connected

to heating coils, located in air handling units, where they may

be exposed to refrigerated air circulation must be equipped with

flow control valves or other automatic means to prevent gravity

circulation of the boiler water during the cooling cycle.

7.5.5

Waterside Flow (primary circuit)

The boiler is designed for closed loop, forced circulation hot

water heating systems only.

Family PRO is equipped with an internal pump.

PUMP DUTY

Residual head of circulator
The residual head for the heating system is represented

in the graph, according to the flow rate. The piping on

the heating system must be sized taking into account the

available residual head value.

Bear in mind that the boiler will operate correctly if there is

sufficient water circulation in the heat exchanger, as the boiler

is equipped with an automatic internal by-pass which is

designed to ensure water flow rate into the heat exchanger is

correct under any installation conditions.

CAUTION

: The Family PRO IS must not be operated as a potable

Hot Water Boiler. The Family PRO must not be operated in a

open system.

Flow rate [gpm]

Residual head [ft]

73 Watt

III

speed

An external CH/System pump and additional bypass (or

hydraulic separator) is required for heating systems outside

the flow requirements of the internal circulator pump. It

is recommended to have a Primary and Secondary loop

configuration with closely spaced Tee’s.

7.6

Making the gas connection

DANGER:

Only carry out work on gas piping and connections

if you are licensed for such work.

− Determine proper size gas pipe for the installation according

to the general and local rules.

− Do not forget the pipe connection losses and observe proper

size of the fittings.

− Install the furnished 3/4” female gas cock on the gas

connection (3/4” male on the boiler).

− Connect the gas pipe to the gas cock so that it is free from any

strain.

WARNING:

Failure to keep boiler area clear and free of

combustible materials, gasoline and other flammable

liquids and vapors can result in severe personal injury,

death or substantial property damage.

WARNING:

Before carrying out the connection, check that

the type of gas is that for which the appliance is set up.

WARNING:

Remove any combustible materials, gasoline and

other flammable liquids awmanuay from the hot water

pipes.

WARNING

: The boiler and its gas connections must be leak

tested before placing the boiler in operation.

CAUTION

: The boiler and its individual shut off valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of

1/2 psi (3.5 kPa).

WARNING

: Before starting the Family PRO, and during initial

operation, smell near the floor and around the boiler for gas

or any unusual odor. Do not proceed with start-up if there is

any indication of a gas leak. Repair any leak at once.

Содержание Family PRO 42 IS













































































Результаты поиска

Содержание Family PRO 42 IS

Отзывы:

Похожие инструкции для Family PRO 42 IS

Бренды по названию

Популярные бренды

Riello Family PRO 42 IS, Инструкция по установке и эксплуатации для подрядчиков

Результаты поиска

Содержание Family PRO 42 IS

Отзывы:

Похожие инструкции для Family PRO 42 IS

Бренды по названию

Популярные бренды