Ricoh TH-C1b Скачать руководство пользователя страница 181

Страница: 181 / 433

SERVICE CALL

10 February 2005

4-14

No.

Definition

Symptom Possible

Cause

Startup without video output end error (Y)

801 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the engine
within the specified time.

•

Defective controller board

Startup without video output end error (M)

802 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the engine
within the specified time.

•

Defective controller board

Startup without video output end error (C)

803 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the engine
within the specified time.

•

Defective controller board

Startup without video input end error (K)

804 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the
scanner within the specified time.

•

Defective controller board

Startup without video input end error (Y)

805 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the
scanner within the specified time.

•

Defective controller board

Startup without video input end error (M)

806 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the
scanner within the specified time.

•

Defective controller board

Startup without video input end error (C)

807 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the
scanner within the specified time.

•

Defective controller board

Startup without video input end error (R)

808 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the
scanner within the specified time.

•

Defective controller board

Startup without video input end error (G)

809 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the engine
within the specified time.

•

Defective controller board

Startup without video input end error (B)

810 B

Video transfer to the engine is
started, but a video transmission end
command is not issued by the engine
within the specified time.

•

Defective controller board

Watchdog error

818 B

While the system program is running,
no other programs can run (due to a
bus hold or endless loop).

•

Defective controller board

Содержание TH-C1b


















































































































































































































































































































































































































































Результаты поиска

Содержание TH-C1b

Отзывы:

Похожие инструкции для TH-C1b

Бренды по названию

Популярные бренды

Ricoh TH-C1b, Руководство по обслуживанию

Результаты поиска

Содержание TH-C1b

Отзывы:

Похожие инструкции для TH-C1b

Бренды по названию

Популярные бренды