Ricoh TH-C1b Скачать руководство пользователя страница 187

Страница: 187 / 433

SELF-DIAGNOSTIC MODE

10 February 2005

4-20

4.2 SELF-DIAGNOSTIC MODE

4.2.1 OVERVIEW

There are three types of self-diagnostics for the controller.

•

Power-on self-diagnostics: The machine automatically starts the self-diagnostics
just after the power has been turned on.

•

Detailed self-diagnostics: The machine does the detailed self-diagnostics by
using a loop-back connector (P/N G0219350)

•

SC detection: The machine automatically detects SC conditions at power-on or
during operation.

The following shows the workflow of the power-on and detailed self-diagnostics.

Power ON

Diagnostic RAM Check

CPU Check

ASIC Check

Standard RAM

Conection Check

Optional RAM

Connection Check

Clock Generator Check

Standard NVRAM

Check

Font Header Check

Optional NVRAM Check

Real Time Clock Check

Network Check

Engine I/F Check

Interrupt Check

Memory Chip Check

Power-on or

Detailed

ROM Sum Check

Standard RAM Detailed

Check

Optional RAM Detailed

Check

Standard NVRAM

Detailed Check

Optional NVRAM

Detailed Check

Optinoal HDD Check

IEEE1284 Loop-back

Check

Real Time Clock

Detailed Check

Font ROM Sum Check

END

Power-on

Detailed

SC821

SC820

SC838

SC826

SC828

SC829

SC826

Error Logged

Not initialized

SC829

SC827

SC824

Not use optional RAM

Error Logged

B156T501.WMF

Содержание TH-C1b


















































































































































































































































































































































































































































Результаты поиска

Содержание TH-C1b

Отзывы:

Похожие инструкции для TH-C1b

Бренды по названию

Популярные бренды

Ricoh TH-C1b, Руководство по обслуживанию

Результаты поиска

Содержание TH-C1b

Отзывы:

Похожие инструкции для TH-C1b

Бренды по названию

Популярные бренды