Ricoh LP131n Скачать руководство пользователя

Страница: 39 / 204

Attaching Gigabit Ethernet Board Type A

• Do not touch the inside of the controller board compartment. Doing so may cause a malfunction or a

burn.

• The printer's ethernet and USB ports are not available when the Gigabit Ethernet board is attached

to the printer. Instead, you can use the ethernet port and USB port mounted on the board.

• Before handling the Gigabit Ethernet board, ground yourself by touching something metal to

discharge any static electricity. Static electricity can damage the Gigabit Ethernet board.

• Do not subject the Gigabit Ethernet board to physical shocks.

Check the contents of the box.

AUB249S

1. Gigabit Ethernet Board

2. Ferrite Core

3. Protective caps (one each for the ethernet port and the USB port)

Turn off the power, and then unplug the power cable.

Attaching Gigabit Ethernet Board Type A

Содержание LP131n












































































































































































































Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды

Ricoh LP131n, Руководство по эксплуатации

Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды