Ricoh LP131n Скачать руководство пользователя

Страница: 101 / 204

You can set the vertical value in the following range: 139.7 mm - 432 mm (5.50 -17.00 inches).

Press the [Online] key.

The initial screen appears.

• The printer driver Help

Specifying a paper type for the bypass tray

By selecting the paper type you want to load, the printer performs better. You can select from the following
paper types:

• Plain Paper, Recycled Paper, Special Paper, Color Paper, Letterhead, Transparency (OHP

transparency), Envelope, Preprinted, Thick Paper

You can select custom paper type settings made using Web Image Monitor.

• Be sure to select the paper type when you load thick paper, envelopes, or OHP transparencies in the

bypass tray.

• The paper type selected using the printer driver overrides that selected using the control panel.
• Be sure to set a paper type using the control panel of the printer as the following procedure. If you

set a paper type only by the printer driver, printing result might not be appropriate.

Press the [Menu] key.

AUB051S

The [Menu] screen appears.

Loading Paper

Содержание LP131n












































































































































































































Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды

Ricoh LP131n, Руководство по эксплуатации

Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды