manualshive.com logo in svg

Ricoh LP131n, Руководство по эксплуатации

Поделиться
Скачать
Ricoh LP131n Скачать руководство пользователя страница 143

Adjusting Tray Registration

You can adjust the registration of each tray. The vertical adjustment is used for all trays. Normally, you
need not update the registration. But when the optional paper feed unit or the duplex unit is installed,
updating is useful in some cases.

1.

Press the [Menu] key.

AUB051S

The [Menu] screen appears.

2.

Press the [ ] or [ ] key to display [Maintenance], and then press the [  Enter] key.

3.

Press the [ ] or [ ] key to display [Registration], and then press the [  Enter] key.

4.

Press the [ ] or [ ] key to display [Prt. Test Sheet], and then press the [  Enter] key.

5.

Press the [ ] or [ ] key to select the tray you want to adjust, and then press the [  Enter]
key.

Print the test sheet to preview the settings.

Adjusting Tray Registration

141

8

Содержание LP131n













































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды