Ricoh LP131n Скачать руководство пользователя

Страница: 193 / 204

Width

Depth

Height

Printer with two
optional paper feed
unit

388 mm (15.2 ")

450 mm (17.7 ")

615 mm (24.2 ")

Weight:

Approximately 17 kg (37.5 lb) (power cord included)

Noise Emission

Sound Power Level : Main frame only

31ppm model printer

36ppm model printer

Stand-by

42 dB (A)

44 dB (A)

During Printing

65 dB (A)

67 dB (A)

Sound Pressure level : Main frame only

31 ppm model printer

36 ppm model printer

Stand-by

36 dB (A)

38 dB (A)

During Printing

59 dB (A)

61 dB (A)

The preceding measurements made in accordance with ISO7779 are actual values.

Measured at the position of a bystander.

Memory:

Standard 192 MB, up to 384 MB (with the optional Memory Unit)

Interface:

Standard:

• Ethernet (10/100Base-TX)
• USB2.0

It requires a USB computer port and cable that support USB2.0.

• Parallel (Bidirectional IEEE1284)

Optional:

• IEEE 802.11b (Wireless LAN)
• Gigabit Ethernet board

Specifications

191

Содержание LP131n












































































































































































































Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды

Ricoh LP131n, Руководство по эксплуатации

Результаты поиска

Содержание LP131n

Отзывы:

Похожие инструкции для LP131n

Бренды по названию

Популярные бренды