Ricoh LP131n Скачать руководство пользователя | Manualshive

Страница: 163 / 204

background image

When Printer is Not Functioning Properly

Paper is not fed from the selected tray.

When you are using a Windows operating system, the printer driver settings override those set using the
control panel. Set the desired input tray using the printer driver.
See the printer driver Help.

It takes too much time to turn on the printer.

If the printer is turned off while it is still accessing the hard disk (for example: during file deletion), the printer
will require more time to power-up the next time it is turned on. To avoid this time delay, do not turn the
power off while it is in operation.

It takes too much time to resume printing.

• Large or complex data takes long time for the printer to process. If the Data In indicator is blinking,

the data is being processed. Just wait until it resumes.

• If OHP transparencies is in use, printing takes more time to start.
• The printer was in the Energy Saver mode. To resume from the Energy Saver mode, the printer has to

warm up, and this takes time until printing starts. To disable the Energy Saver mode, select [Off] for
[Energy Saver] in the [System] menu.

• Changing the paper feed direction may sometimes reduce the time to resume printing.

It takes too much time to complete the print job.

• Photographs and other data intensive pages take a long time for the printer to process, so simply wait

when printing such data.
Changing the settings with printer driver may help to speed up printing.
See the printer driver Help.

• Large or complex data takes long time for the printer to process. If the Data In indicator is blinking,

the data is being processed. Just wait until it resumes.

• If "Waiting..." appears on the display, the printer is now warming up. Wait for a while.

Network configurations you have made do not become effective.

Print a configuration page and check the network settings.

The control panel error message stays on after removing the misfed paper.

Open the front cover of the printer and then close it.
See p.167 "Removing Misfed Paper".

Other Printing Problems

161

9

«
...
161
162
163
164
165
...
»

Содержание LP131n













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LP131n

Бренд: Unitech Страницы: 2

M-Class Mark II

Бренд: Datamax Страницы: 94

Бренд: Datamax Страницы: 2

Бренд: Durst Страницы: 2

Бренд: Oki Страницы: 126

Бренд: Oce Страницы: 222

Бренд: Muratec Страницы: 6

Бренд: Ricoh Страницы: 130

Бренд: Kyocera Страницы: 28

Бренд: Star Micronics Страницы: 127

Бренд: ZKTeco Страницы: 38

Бренд: Lexmark Страницы: 2

WORKCENTRE 7755

Бренд: Xerox Страницы: 20

ML-2010 - B/W Laser Printer

Бренд: Samsung Страницы: 142

SCX-5635FN - Mono Laser P/s/c/f USB Enet 1200X1200 128MB 35PPM

Бренд: Samsung Страницы: 6

SCX-5635 Series

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 8

Бренд: Samsung Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды