manualshive.com logo in svg

Renesas HD6417641, Руководство по оборудованию, Страница: 649 / 1036

Поделиться
Скачать
Renesas HD6417641 Скачать руководство пользователя страница 649

Section 18   Multi-Function Timer Pulse Unit (MTU) 

 

 

Rev. 4.00  Sep. 14, 2005  Page 599 of 982 

 

 REJ09B0023-0400 

Dead Time Setting: In complementary PWM mode, PWM pulses are output with a non-
overlapping relationship between the positive and negative phases. This non-overlap time is called 
the dead time. 

The non-overlap time is set in the timer dead time data register (TDDR). The value set in TDDR is 
used as the TCNT_3 counter start value, and creates non-overlap between TCNT_3 and TCNT_4. 
Complementary PWM mode should be cleared before changing the contents of TDDR. 

PWM Cycle Setting: In complementary PWM mode, the PWM pulse cycle is set in two 
registers

TGRA_3, in which the TCNT_3 upper limit value is set, and TCDR, in which the 

TCNT_4 upper limit value is set. The settings should be made so as to achieve the following 
relationship between these two registers: 

TGRA_3 set value = TCDR set value + TDDR set value 

The TGRA_3 and TCDR settings are made by setting the values in buffer registers TGRC_3 and 
TCBR. The values set in TGRC_3 and TCBR are transferred simultaneously to TGRA_3 and 
TCDR in accordance with the transfer timing selected with bits MD3 to MD0 in the timer mode 
register (TMDR). 

The updated PWM cycle is reflected from the next cycle when the data update is performed at the 
crest, and from the current cycle when performed in the trough. Figure 18.36 illustrates the 
operation when the PWM cycle is updated at the crest. 

See the following part, Register Data Updating, for the method of updating the data in each buffer 
register. 

Содержание HD6417641













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов