Regency Horizon HZ40E Скачать руководство пользователя

Страница: 45 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

OPTIONAL FAN INSTALLATION - EXISTING INSTALL

120 Volt AC power is needed for the fan switch and blower. The fan can
be hard wired if desired.The receptacle box should be installed on the left

hand side of the unit by a qualiied electrician.The neutral (wider) slot of the

polarized receptacle should be at the top (see page 41 for wiring diagram).

Unit must be grounded at all times. Do not cut the ground terminal off
under any circumstances.

Shut off

the

gas and power supply to the unit.

Remove the faceplate, mesh guard, enamel panels (if installed) and the

glass door. (See the manual for detailed instructions)

Remove the inner panels - reverse of "Inner panel Installation" in the

installation manual.

Remove the burner tray cover by lifting up and out as shown below.

* Prior to removing burner - remove crystals, pebbles, spa stones and inner

panels - if installed.

Loosen 3 screws at the back of the burner to release it.

Remove the burner by sliding it to the right - then lift out.

Remove the left access plate by undoing the 8 screws - see locations

below.

Remove the valve tray by undoing the 8 screws - see locations below.

Location of screws on access plate

Manoeuvre fan through left access panel opening.

Содержание Horizon HZ40E









































































Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды

Regency Horizon HZ40E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды