Harman Home Heating Harman Accentra Insert Скачать руководство пользователя

Страница: 1 / 48

SAFETY NOTICE

PlEASE rEAd ThIS ENTIrE mANuAl bEFOrE YOu INSTAll ANd uSE YOur NEw rOOm hEATEr. FAIlurE

TO FOllOw INSTruCTIONS mAY rESulT IN PrOPErTY dAmAgE, bOdIlY INjurY, Or EvEN dEATh.

FOr uSE IN ThE u.S. ANd CANAdA. SuITAblE FOr INSTAllATION IN mObIlE hOmES

IF ThIS APPlIANCE IS NOT PrOPErlY INSTAllEd, A hOuSE FIrE mAY rESulT. FOr YOur SAFETY, FOllOw

INSTAllATION dIrECTIONS. dO NOT uSE mAkEShIFT COmPrOmISES.

CONTACT lOCAl buIldINg Or FIrE OFFICIAlS AbOuT rESTrICTIONS ANd INSTAllATION INSPECTION

rEQuIrEmENTS IN YOur ArEA.

CONTACT YOur lOCAl AuThOrITY (SuCh AS muNICIPAl buIldINg dEPArTmENT, FIrE dEPArTmENT, FIrE

PrEvENTION burEAu, ETC.) TO dETErmINE ThE NEEd FOr A PErmIT.

CETTE guIdE d'uTIlISATION EST dISPONIblE EN FrANCAIS. ChEz vOTrE CONCESSIONNAIrE dE

hArmAN.

SAvE ThESE INSTruCTIONS.

The harman Accentra Pellet Insert

Installation & Operating manual

“Ce manuel est disponible en Français sur demande”

R15

Item# 3-90-00674

This Fireplace insert may be installed into a masonry

fireplace, an approved manufactured wood burning fireplace

(see page 25), Or, It may be built in to a wall or mantle system

when using the optional zero clearance cabinet (see page 26).

Содержание Harman Accentra Insert

















































Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды

Harman Home Heating Harman Accentra Insert, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды