background image

25

Installing the Accentra Insert into an 

existing factory built wood burning 

fireplace

When installing the Accentra Insert into a factory 

built wood burning fireplace, the Manufactured Fire-

place Installation Kit # 1-00-674205 must be used. In 

addition, several things need to be taken into consid-

eration.

The size of the fireplace opening. Will the unit fit 

into  the  opening?  Many  of  these  units  have  metal 

smoke shields inside the top that can be removed to 

gain height. Often the side and rear refractory can be 

removed to gain depth and width. In some circum-

stances, the front lower lip or grill work may also be 

removed. Be sure and follow the guidelines in the kit 

instructions.

 Because of the special track system, it 

is also permitted to remove the floor refractory and/or 

insulation in the bottom of the manufactured fireplace, 

right down to the outer sheet metal, which must be left 

in place for floor protection under the insert mounting 

frame. Floor protection guidelines, as listed on page 

14 must also be followed.  

OPTIONAl  hOPPEr  CONFIgurATIONS  FOr  SmAllEr 

FIrEPlACE OPENINgS:

The Harman Accentra Insert can be factory built with shorter 

hopper configurations.

The standard requires a 24" opening. Part #1-90-00674

Option 1: Requires a 22" opening height. Part #1-90-00675

Option 2: Requires a 20" opening height. Part #1-90-00676

Keep in mind the hopper capacities will decrease with the optional 

heights.

venting

Note: If the Harman Accentra Insert is installed into a factory built wood burning fireplace, 

this label (harman part #  3-90-00675) muST be attached to the altered fireplace. This label is 

included in the Manufactured fireplace installation kit.

Fig. 53

Fig. 54

Содержание Harman Accentra Insert

















































Отзывы: