Harman Home Heating Harman Accentra Insert Скачать руководство пользователя

Страница: 10 / 48

Installation

2. Remove the door by swinging it open approximately

and lift it upward until it clears the hinge pins.

3. Remove the ash pan

4. Remove the (4) internal pieces of cast iron. See Fig.

14 and 15.

How to Reduce the Weight for Installation, cont'd

Removing the Center Medallion

•

Lift up on the 2 bottom corners of the medallion until

it is higher than the top of the flame guide.

•

Pull the bottom edge of the medallion front approxi-

mately 1 inch.

•

Pull downward on the corners of the medallion until

the top is released from the 2 retainers that keep the

top aligned when in place.

•

Note: The heat exchanger covers will tilt to the front

when the center medallion is removed.

Removing the Heat Exchanger Covers

•

Remove the heat exchanger cover by lifting it upward

about 1/2 inch and move the bottom edge front until it

sits flat on the firebox bottom.

•

Rotate the edge of the heat exchanger closest to the

burnpot until it is in front of the burnpot.

•

Tip the top of the heat exchanger toward the middle

of the opening until it can be lifted up and out.

Center medallion

Flame guide

burn Pot

: dOwN

:uP

: OuT

:uP

Fig. 14

Lasered hinge pin

pivoting point

Up and down clearance

adjustment slots.

Cast side

panel hinge

Fig. 13

Lifting tab

Fig. 15

Remove the cast side panels by lifting them upward

off of the hinge pins. See Fig. 13.

Содержание Harman Accentra Insert

















































Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды

Harman Home Heating Harman Accentra Insert, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды