Harman Home Heating Harman Accentra Insert Скачать руководство пользователя

Страница: 11 / 48

Installation

ImPOrTANT:

The mounting frame/surround assembly

and flue piping is the most critical part of the installation

and must be done correctly and installed

securely.

. Choose the chimney configuration that is best suited

for the installation. See venting section. Page 21

• Note: If 100% outside air is desired or required, the

outside air option will need to be installed on the stoves

body. (See instructions included with outside air kit (part

#1-00-674080.) See Page 22.

Make sure the unit will fit into the fireplace opening.

When installing in smaller fireplaces, test fit the mounting

frame into the firebox. Note: The unit overhangs to the

rear. See Fig. 17

Install the 3 piece cast surround set to the sides

and top of the mounting frame with the bolts and nuts

supplied. The left and right side should be done before

the center section is installed. Make sure the bolts are

loose. Do not remove the side panel hinges. The left and

right side wings should be standing up aligned with the

side of the mounting frame and slid inward towards the

center. Note:The wings mount on the rear side below

the notch and on the front side above the notch. See

Fig. 16 & 18. Slide the cast ash lip onto the frame and

check to make sure it can go against the roped frame

rails and fits into the pockets on the left and right cast

sides. See Fig. 19.

Install the center section.

If the wing extension is required, it should be installed

next.

beginning Installation

NOTE: The stove body extends through the mounting

frame in the rear approximately 2".

Approximately 2" overhang

Fig. 17

Cast in front of

the frame. Use

(1)1/4-20 x 3/8

flange bolt from

the rear.

Cast behind the

mounting frame

flange. Use (2)

1/4-20x5/8 flange

bolts and nuts

with bolts from

the front.

Fig. 18

Slide the ash lip

casting into the

frame, making

certain the ash

lip is sitting on

the slide rails on

either side. With

the ash lip in

place, adjust the

surround sides so

there is an even

gap where the

ash lip extends

into the surround

side and tighten.

Fig. 19

3" Outside Air

starter collar

Fig. 16

Notch

Ash lip slide rails

Содержание Harman Accentra Insert

















































Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды

Harman Home Heating Harman Accentra Insert, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Harman Accentra Insert

Отзывы:

Похожие инструкции для Harman Accentra Insert

Бренды по названию

Популярные бренды