Heat&Glo GRAND-I35-C Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 50

background image

1

Heat & Glo • Grand-I35-C, Grand-I35-SP, Supreme-I30-C, Supreme-I30-SP • 2206-901 Rev. J • 11/12

Models:

GRAND-I35-C
GRAND-I35-SP
SUPREME-I30-C
SUPREME-I30-SP

•

DO NOT

store or use gasoline or other fl am-

mable vapors and liquids in the vicinity of this
or any other appliance.

• What to do if you smell gas

-

DO NOT

try to light any appliance.

-

DO NOT

touch any electrical switch.

DO

NOT

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas suppli-
er’s instructions.

- If you cannot reach your gas supplier, call

the fi re department.

• Installation and service must be performed

by a qualifi ed installer, service agency, or the
gas supplier.

WARNING: If the information in these

instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.

Owner’s Manual

Installation and Operation

DO NOT DISCARD THIS MANUAL

NOTICE

This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer’s instructions
and the manufactured home construction and safety standard,

Title 24 CFR, Part 3280

or

Standard for Installation in Mobile

Homes, CAN/CSA Z240MH, in Canada.

This appliance is only for use with the type(s) of gas indicated
on the rating plate.

Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.

• Leave this manual with

party responsible for use
and operation.

DO NO

T

DISCARD

WARNING

• Important operating

a n d m a i n t e n a n c e
instructions included.

• Read, understand and follow

these instructions for safe
installation and operation.

In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.

A CO detector shall be installed in the room where the appliance
in installed.

This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.

HOT SURFACES

!

Glass and other surfaces are hot during
operation AND cool down.

Hot glass will cause burns.

•

DO NOT

touch glass until it is cooled

• NEVER allow children to touch glass
• Keep children away

• CAREFULLY SUPERVISE children in same room as

fi replace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other fl ammable
materials.

• Keep clothing, furniture, draperies and other fl ammable

materials away.

1
2
3
...
»

Содержание GRAND-I35-C



















































Отзывы:

Нет отзывов

Похожие инструкции для GRAND-I35-C

Бренд: Obadiah's Wood Stoves Страницы: 17

Бренд: L'Artistico Страницы: 48

LUNA 850 V Gold Gas

Бренд: M Design Страницы: 39

Бренд: Valor Fires Страницы: 12

Бренд: Duraflame Страницы: 8

Superior Fireplaces Merit WRT2042WS

Бренд: IHP Страницы: 24

Бренд: Heatilator Страницы: 3

astria Mission Mission42TMN

Бренд: IHP Страницы: 32

Бренд: Austroflamm Страницы: 114

Бренд: barbas Страницы: 84

Marquis MCVP42LP

Бренд: Kingsman Fireplaces Страницы: 75

WM -FM L-26-3223-STL

Бренд: Sierra Flame Страницы: 23

Бренд: EINHELL Страницы: 84

Бренд: eligent Страницы: 4

Бренд: Stellar Hearth Страницы: 37

Бренд: RAIS Страницы: 11

Бренд: Hargrove Страницы: 10

Бренд: livn Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды