Heat&Glo GRAND-I35-C Скачать руководство пользователя | Manualshive

Страница: 12 / 50

background image

Heat & Glo • Grand-I35-C, Grand-I35-SP, Supreme-I30-C, Supreme-I30-SP • 2206-901 Rev. J • 11/12

12

Initial Break-in Procedure

• The appliance should be run three to four hours

continuously on high.

• Turn the appliance off and allow it to completely cool.

• Remove fi xed glass assembly. See Section 12.H.

• Clean fi xed glass assembly. See Section 3.

• Replace the fi xed glass assembly and run continuously

on high an additional 9 hours.

This cures the materials used to manufacture the fi re-
place.

NOTICE! Open windows for air circulation during ap-
pliance break-in.

• Some people may be sensitive to smoke and odors.
• Smoke detectors may activate.

K. After Appliance is Lit

L. Frequently Asked Questions

ISSUE

SOLUTIONS

Condensation on the glass

This is a result of gas combustion and temperature variations. As the appliance warms, this
condensation will disappear.

Blue fl ames

This is a result of normal operation and the fl ames will begin to yellow as the appliance is al-
lowed to burn for 20 to 40 minutes.

Odor from appliance

When fi rst operated, this appliance may release an odor for the fi rst several hours. This is caused
by the curing of the paint and the burning off of any oils remaining from manufacturing. Odor may
also be released from fi nishing materials and adhesives used around the appliance.

Film on the glass

This is a normal result of the curing process of the paint and logs. Glass should be cleaned
within 3 to 4 hours of initial burning to remove deposits left by oils from the manufacturing
process. A non-abrasive cleaner such as gas fi replace glass cleaner may be necessary. See
your dealer.

Metallic noise

Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.

Is it normal to see the pilot fl ame burn
continually?

In an intermittent pilot ignition system (IPI), the pilot fl ame should turn off when appliance is
turned off. Some optional control systems available with IPI models may allow pilot fl ame to
remain lit. In a standing pilot system the pilot will always stay on.

«
...
10
11
12
13
14
...
»

Содержание GRAND-I35-C



















































Отзывы:

Нет отзывов

Похожие инструкции для GRAND-I35-C

Бренд: GBT Страницы: 18

PALERMO L FTA90546

Бренд: MWH Страницы: 54

Бренд: Jøtul Страницы: 72

CLASSIC BELL SMALL 3 PF

Бренд: Bellfires Страницы: 88

Бренд: Gasmate Страницы: 12

astria Mission Mission42TMN

Бренд: IHP Страницы: 32

Бренд: United States Stove Страницы: 4

PONDEROSA LS-24P-1

Бренд: White Mountain Hearth Страницы: 12

Бренд: KAL-FIRE Страницы: 72

Бренд: Barbecook Страницы: 11

Nestor Martin 023

Бренд: Euroheat Страницы: 32

Бренд: Mosaic Страницы: 17

Riverview RDV4136

Бренд: Majestic fireplaces Страницы: 2

Бренд: Comfort Glow Страницы: 16

Бренд: Empire Comfort Systems Страницы: 4

Бренд: glamour Страницы: 12

Бренд: IHP Страницы: 2

Бренд: Jøtul Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды