background image

Heat & Glo  • Grand-I35-C, Grand-I35-SP, Supreme-I30-C, Supreme-I30-SP  •  2206-901 Rev. J  •  11/12 

2

Listing Label Information/Location

Model Name: ___________________________________________ Date purchased/installed: __________________

Serial Number: __________________________________________ Location on fi replace: _____________________

Dealership purchased from:  _______________________________ Dealer Phone:  __________________________

Notes: _______________________________________________________________________________________

_____________________________________________________________________________________________

A. Congratulations

Congratulations on selecting a Heat & Glo gas fi replace, an 
elegant and clean alternative to wood burning fi replaces. 
The Heat & Glo gas fi replace you have selected is designed 
to provide the utmost in safety, reliability, and effi ciency.

As the owner of a new fi replace, you’ll want to read and 
carefully follow all of the instructions contained in this 

Owner’s Manual

. Pay special attention to all cautions and 

warnings.

This 

Owner’s Manual 

should be retained for future 

reference. We suggest that you keep it with your other 
important documents and product manuals.

The information contained in this 

Owner’s Manual

, unless 

noted otherwise, applies to all models and gas control 
systems.

Your new Heat & Glo gas fi replace will give you years of 
durable use and trouble-free enjoyment. Welcome to the 
Heat & Glo family of fi replace products!

We recommend that you record the following pertinent 
information about your fi replace.

Gas and Electric 
Information

Serial Number

Type of Gas

The model information regarding your specifi c fi replace can be found on 
the rating plate usually located in the control area of the fi replace.

Homeowner Reference Information

Model Number

Not 

Not for 

for use 

use with 

with solid 

solid fuel.

fuel.

((

Ne 

Ne doit 

doit pas 

pas entre 

entre utilise 

utilise avec 

avec un 

un combustible 

combustible solide).

solide).

This 

This appliance 

appliance must 

must be 

be installed 

installed in 

in accordance 

accordance with 

with local 

local codes, 

codes, if 

if any; 

any; if 

if not, 

not, follow 

follow ANSI 

ANSI Z223.1

Z223.1

in 

in the 

the USA 

USA or 

or CAN/CGA 

CAN/CGA B149 

B149 installation 

installation codes. 

codes. 

(Installer 

(Installer l’appareil 

l’appareil selon 

selon les 

les codes 

codes ou 

ou reglements

reglements

locaux 

locaux ou, 

ou, en 

en l’absence 

l’absence de 

de tels 

tels reglements, 

reglements, selon 

selon les 

les codes 

codes d’installation 

d’installation CAN/CGA-B149.)

CAN/CGA-B149.)

Type 

Type of 

of Gas 

Gas 

(Sorte 

(Sorte De 

De Gaz)

Gaz)

::

N

NA

ATURAL

TURAL  GAS

GAS

MADE 

MADE   IN 

IN   USA

USA

Minimum 

Minimum Permissible 

Permissible Gas 

Gas Supply 

Supply for 

for Purposes 

Purposes of 

of Input 

Input Adjustment.

Adjustment.

Approved 

Approved Minimum 

Minimum 

(De 

(De Gaz) 

Gaz) 

Acceptable

Acceptable

0.0

0.0  in 

in w.c.

w.c.

(Po. 

(Po. Col. 

Col. d’eau)

d’eau)

Maximum 

Maximum Pressure 

Pressure 

(Pression)

(Pression)

  0.0

0.0  in 

in w.c.

w.c.

(Po. 

(Po. Col. 

Col. d’eau)

d’eau)

Maximum 

Maximum Manifold 

Manifold Pressure 

Pressure 

(Pression)

(Pression)

   

   0.0

0.0  in 

in w.c.

w.c.

(Po. 

(Po. Col. 

Col. d’eau)

d’eau)

Minimum 

Minimum Manifold 

Manifold Pressure 

Pressure 

(Pression)

(Pression)

   

   0.0

0.0  in 

in w.c.

w.c.

(Po. 

(Po. Col. 

Col. d’eau)

d’eau)

Model:

Model:
(Modele):

(Modele):

Serial

Serial
(Serie):

(Serie):

ANSI 

ANSI Z21XX-XXXX 

Z21XX-XXXX · 

· CSA 

CSA 2.XX-MXX 

2.XX-MXX   · 

· UL307B

UL307B

XXXXXXXX

XXXXXXXX

IN 

IN CANADA

CANADA

ALTITUDE:

ALTITUDE:

0-0000 

0-0000 FT.

FT.

0000-0000FT.

0000-0000FT.

MAX. 

MAX. INPUT 

INPUT BTUH:

BTUH:

00,000

00,000

00,000

00,000

MIN. 

MIN. INPUT 

INPUT BTUH:

BTUH:

00,000

00,000

00,000

00,000

ORIFICE 

ORIFICE SIZE:

SIZE:

#XXXXX

#XXXXX

#XXXXX

#XXXXX

XXXXXXXX

XXXXXXXX

Total 

Total Electrical 

Electrical Requirements: 

Requirements: 000Vac, 

000Vac, 00Hz., 

00Hz., less 

less than 

than 00 

00 Amperes

Amperes

 

 
 

 

Heat & Glo, a brand of Hearth & Home Technologies, Inc.
7571 215th Street West, Lakeville, MN   55044

Read this manual before installing or operating this appliance. 

Please retain this owner’s manual for future reference.

Содержание GRAND-I35-C



















































Отзывы: