manualshive.com logo in svg

Regency Horizon HZ40E, Инструкция для владельца и по установке

Поделиться
Скачать
Regency Horizon HZ40E Скачать руководство пользователя страница 50

50

 | 

Regency Horizon® HZ40E-10 Gas Fireplace

 | 

50

installation

INNER PANEL INSTALLATION

1)

 

Remove the faceplate and glass door if already installed - see 

       manual for instructions.

2)

 

Remove 4 screws to remove

 top heat defl ector.

7)

 

Install the left side enamel panel - secure in position with the panel clip 
and tighten two screws loosened in step 3 as shown in the diagram 
below.

8)

 

Install the right side enamel panel - secure in position with the panel 
clip and two screws loosened in step 4.

9)

   Reinstall heat defl ector.

10)

 Reinstall glass door - reinstall faceplate.

4) 

Repeat on opposite side.

5)

  Remove back panel.

6) 

Install the back enamel panel fi rst.  Tilt the panel forward - position 
the bottom of the panel fi rst.  Use care not to scratch or mark the 
panel on the pilot shield.

Final Install

3)

 

Remove installed factory panels.

 

  

Loosen 2 screws (do not remove) on panel clip securing side panel,

 

Slide panel clip down away from screws.

 

Remove side panel.

Handling Instructions

Black Enamel Panels

•

 Black Enamel panels must be inspected for scratches and dimples 

prior to installation.  All claims to be recorded at this time.  
Claims for damage after installation will not receive consideration.

•

 Black Enamel panels will discolor a little during normal operation.  

This is normal and should not be considered a defect.

*All  hand  and  fi nger  marks 

MUST

  be  cleaned  off  with  a  soft  cloth.    

Use  an  ammonia  based  cleaner  (ie. glass  cleaner)  to  remove  any 
fi ngerprints before applying heat to the unit.

Failure to do this will result in burn stain on panels which you will 
be unable to remove.

  Not protected by product warranty.  

Panel clip

INNER PANEL INSTALLATION

Содержание Horizon HZ40E









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды