Regency Horizon HZ40E страница 59 Скачать руководство пользователя | Manualshive

Страница: 59 / 72

background image

Regency Horizon® HZ40E-10 Gas Fireplace

|

59

|

59

operating instructions

LIGHTING PROCEDURE

IMPORTANT:

The remote control system supplied with this appliance has

several options for starting/operating the appliance using the power button

and ON/OFF key on the hand held transmitter.

Prior to operating this appliance,

please read the remote control operating

instructions (packaged with remote control) to understand how to operate

this remote control system. Option to download remote functions video
with QR code below.

1.

Ensure the wall switch/receiver is in the remote position. (see Diagram 1).

3

. After approximately 4 seconds the spark ignition system will spark for 60

seconds to light the main burner.

4.

The unit will turn on.

Note:

The irst try for ignition will last approximately 60 seconds. If there is no

lame ignition (rectiication) the board will stop sparking for approximately
35 seconds. After wait time , the board will start second try for ignition by
sparking for approximately 60 seconds. If there is still no positive ignition
the board will go into lock out.

The system will need to be reset as follows:

a)

Turn the system of using ON/OFF switch or press ON/OFF button - if

using remote.

b)

After approximately 2 seconds turn on ON/OFF switch or press ON/OFF

button if using remote.

c)

Repeat step 2.

ON/OFF

Button

Diagram 1

Diagram 2

Set Switch to

Remote

SHUTDOWN

PROCEDURE

1.

Turn the wall mounted switch or remote to the "OFF" position.

2.

Press "OFF" on the remote control.

3.

Turn the gas control knob to the "OFF" position to turn of the pilot.

Remote shown in Manual Mode on Hi

Prolame

video

2.

Press and release the ON/OFF button on the remote handheld transmit

-

ter (see Diagram 2). An audible beep should be heard from the receiver.

«
...
57
58
59
60
61
...
»

Содержание Horizon HZ40E









































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ40E

Бренд: Belleze Страницы: 12

Бренд: Quadra-Fire Страницы: 36

Бренд: Majestic Страницы: 8

Бренд: Napoleon Страницы: 128

Бренд: HAMPTON BAY Страницы: 60

CORINTHIA BLACK NG

Бренд: superior fires Страницы: 12

Бренд: superior fires Страницы: 5

Бренд: Dru Страницы: 24

STONEFIRE SF10BL

Бренд: Valor Страницы: 20

Бренд: Boulevard Страницы: 48

Бренд: Superior Fireplaces Страницы: 32

Бренд: Coleman Страницы: 16

Бренд: Febo Flame Страницы: 9

61204005-810392525

Бренд: Febo Страницы: 16

Бренд: Bio Flame Страницы: 7

Бренд: IHP Страницы: 2

Arch Screen Door Kit GABS4S0

Бренд: Majestic fireplaces Страницы: 2

Бренд: Majestic fireplaces Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды