Regency Horizon HZ40E Скачать руководство пользователя

Страница: 53 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

. Position Left Log (2) by matching the log and template proﬁ les exactly.

. Position Right Log (3) by matching the log and template proﬁ les exactly.

. Position Left Cross Log (4) on Log 1, match up pin landing as per

reference below, rest bottom of Log 2 on Log 3 plus match log proﬁ le
with template proﬁ le.

. Position Right Cross Log (5) by lining pin on Logs 1 with pin landing

on Log 3, match bottom of Log 5 and template proﬁ le.

. Carefully remove magnets and log placement template, slightly lifting

logs as required.

. Place Front Left log piece on ﬁ rebox ﬂ oor as shown.

. Place Right Log piece on ﬁ rebox ﬂ oor as shown.

. If desired, install additional crystals on ﬁ rebox ﬂ oor, in and around

installed logs.

18.

Install lava embers - spread evenly over glass.

HZ54E shown - Left Log (2) positioned to match

template proﬁ le.

HZ54E shown - Completed Install

HZ40E shown - Completed Install

HZ54E shown - Left Cross Log (4) positioned to

match template proﬁ le.

HZ54E shown - Right Log (3) positioned to match

template proﬁ le.

HZ54E pin landing

HZ40E pin landing

HZ54E shown - Left Log Piece(6)

HZ54E shown - Right Log Piece(7)

Lava embers on glass crystals

Match pin and pin landing

Logs 1 and 3.

19.

Reverse steps 1 and 2.

20.

Adjust aeration settings - see unit manual for settings.

Содержание Horizon HZ40E









































































Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды

Regency Horizon HZ40E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды