Regency Horizon HZ40E Скачать руководство пользователя

Страница: 29 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

VERTICAL TERMINATIONS

RIGID PIPE 4" X 6-5/8

The minimum components required for a basic vertical

termination are:

1 Vertical Termination Cap

1 45

Elbow

1 Rigid Pipe Adaptor (510-994)

1 Ceiling Firestop
1 Flashing
1 Storm Collar

1 Length of pipe to suit wall thickness

(see chart)

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

This product has been evaluated by Intertek for using a Rigid Pipe Adaptor in conjunction

with Duravent Direct-Vent, Selkirk Direct-Temp, Ameri Vent Direct Venting, ICC Excel Direct

and Security Secure Vent systems. Use of these systems with the Rigid Pipe adaptor is

deemed acceptable and does not afect the Intertek WHI listing of components.

WARNING:

Do not combine venting components from diferent venting systems.

However use of the the AstroCap

and FPI Riser is acceptable with all systems.

The FPI AstroCap

and FPI Riser Vent terminal are certiied for installations using FPI venting systems as well as Simpson Dura-Vent

Direct Vent,

American Metal Products Ameri Vent Direct Vent, Security Secure Vent

, ICC Excel, Selkirk Direct-Temp. AstroCap

is a proprietary trademark of FPI

Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

Pipe

Length

Vertical Terminal

Storm Collar

Flashing

Ceiling Firestop

Adj.Pipe Length

Vinyl Siding

Standoff (Optional)

Rigid Pipe Adapter

45 Elbow

Galvanized pipe is desirable above the rooline due to its higher

corrosion resistance. Continue to add pipe sections through the

lashing until the height of the vent cap meets the minimum height

requirements speciied in Dia. 4 or local codes. Note that for steep

roof pitches, the vertical height must be increased. A poor draft, or

down drafting can result from high wind conditions near big trees

or adjoining roof lines, in these cases, increasing the vent height

may solve the problem.

Roof Pitch

Minimum Vent Height

Feet

Meters

lat to 7/12

0.61

over 7/12 to 8/12

0.61

over 8/12 to 9/12

0.61

over 9/12 to 10/12

2.5

0.76

over 10/12 to 11/12

3.25

0.99

over 11/12 to 12/12

1.22

over 12/12 to 14/12

1.52

over 14/12 to 16/12

1.83

over 16/12 to 18/12

2.13

over 18/12 to 20/12

7.5

2.29

over 20/12 to 21/12

2.44

Содержание Horizon HZ40E









































































Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды

Regency Horizon HZ40E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды