Regency Horizon HZ40E Скачать руководство пользователя

Страница: 44 / 72

Regency Horizon® HZ40E-10 Gas Fireplace

installation

11. Install the fan control module (FCM) into the bracket on the side access

panel. Plug in the power cord to the outlet in the unit. Reinstall the panel

with the 4 screws from step 10.

12. Plug in the fan power cord to the Fan Control Module into the outlet

marked “Fan”. Plug the FCM-COM wire from the remote control wiring

harness into the location on the Fan Control Module marked “COM”.

Turn the switch on the Fan Control Module to the ON position. ON is to

the left. The “O” is the off position

FCM-COM connector

TO REMOVE THE FAN

Turn the power off.

Reverse the above instructions.

Maintenance:

The sealed bearings are lubricated, there is no need to lu-

bricate them further. (Extra lubricant will cause more lint and dust buildup

- causing the bearings to prematurely fail).

Regular cleaning and vacuuming of the fan area will add to the life of the

motor.

IMPORTANT:

These fans collect a lot of dust from within your home. Ensure you

maintain these fan motors on a regular basis by vacuuming

the fan blades and housing using a soft brush nozzle.

Содержание Horizon HZ40E









































































Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды

Regency Horizon HZ40E, Инструкция для владельца и по установке

Результаты поиска

Содержание Horizon HZ40E

Отзывы:

Похожие инструкции для Horizon HZ40E

Бренды по названию

Популярные бренды