manualshive.com logo in svg

Regency Horizon HZ40E, Инструкция для владельца и по установке

Владельцы и руководство по установке для камина Regency Horizon HZ40E доступно для загрузки бесплатно на manualshive.com. Получите доступ к полезному руководству, чтобы наслаждаться уютной и теплой атмосферой в вашем доме. Перейдите на сайт сейчас, чтобы скачать необходимое руководство.

Поделиться
Скачать
background image

4

 | 

Regency Horizon® HZ40E-10 Gas Fireplace

 | 

4

table of contents

Installation 

Copy of Safety Decal .....................................................5
MA Code - CO Detector ................................................6
Important Message   ......................................................8
Before You Start .............................................................8
General Safety Information ............................................8
Installation Checklist ......................................................9
Locating Your Gas Fireplace ..........................................9
Heatwave Duct System .................................................9
Heat Release kit ............................................................9
Clearances ..................................................................10
Mantel Clearances .......................................................11
Mantel Leg Clearances ................................................11
Unit Assembly Prior To  
Installation ...................................................................12
Nailing Strips ...............................................................12

Installation Access panel .....................................12

Framing Dimensions ....................................................13
Optional Framing kit .....................................................14
Wall mount On / Off Switch and remote receiver  
installation ....................................................................15
Non-Combustible Requirements..................................16
Non-combustible facing installation  ............................16
Framing & Finishing .....................................................17
Exterior Vent Termination Requirements .....................19
4” x 6-5/8” Rigid Pipe  ..................................................20
Cross Reference Chart only ........................................20
Vent Restrictor Position ...............................................22
Venting Introduction .....................................................23
Venting Arrangement for Horizontal Terminations .......23
Horizontal Terminations ...............................................24
Flex Vent 4" x 6-7/8" ....................................................24
Horizontal terminations ................................................25
Rigid Pipe 4" x 6-5/8" ...................................................25
Horizontal Terminations ...............................................26
Rigid Pipe 4" x 6-5/8" ...................................................26
Vertical terminations ....................................................29
Rigid Pipe 4" x 6-5/8" ...................................................29
Venting Arrangement for Vertical Terminations ............30
Vertical Termination with Co-Linear Flex System ........31
Vertical Terminations ...................................................32
Rigid Pipe 4" x 6-5/8" ...................................................32
Venting Arrangements - Vertical Terminations  ............34
Unit Installation with Horizontal Termination  ...............35
4" x 6-5/8" venting .......................................................35
Unit Installation with Horizontal Termination  ...............36
Dura-Vent Horizontal terminations ...............................37
Unit installation with Vertical Termination .....................38

4" x 6-5/8" venting .......................................................38
Vertical Termination  ....................................................39
4" x 6-5/8" venting .......................................................39
Flex vent components ..................................................40
High Elevation ..............................................................41
Gas Line Installation ....................................................41
Pilot Adjustment ...........................................................41
Gas Pipe Pressure Testing ..........................................41
885 S.I.T. Valve Description .........................................41
Aeration Adjustment ....................................................41
Wiring diagram ............................................................42
Optional fan Installation - initial install .........................43
Optional fan Installation - existing install ......................45
Wiring diagram with optional fan .................................48
Optional wall thermostat installation ............................49
Inner Panel Installation ................................................50
Glass Crystals or optional stones ................................51
Installation On Burner ..................................................51
Optional Pebbles / Glass crystal Installation for Firebox 
Base (around burner) ..................................................51
Optional driftwood Log set Installation .........................52
Glass door Installation .................................................54
Safety screen/inner door frame removal/ Installation ..55
Verona / 4 piece faceplate installation .........................56
Outer door frame installation .......................................57

Operating Instructions

Operating Instructions .................................................58
First Fire ......................................................................58
Normal Operating Sounds of Gas Appliances .............58
Lighting Procedure ......................................................59
Copy of Lighting Plate Instructions ..............................60

Maintenance

Maintenance Instructions ............................................61
Glass Gasket ...............................................................61
Glass Door ...................................................................61

Glass Replacement .............................................61

General Vent Maintenance ..........................................61
Valve assembly Replacement ......................................62

Parts

Main Assembly ............................................................63
Accessories .................................................................64

Warranty

Warranty ......................................................................66

Содержание Horizon HZ40E









































































Отзывы:

Нет отзывов

Похожие инструкции для Horizon HZ40E

Valor British Gas BG C-2 Installer'S Manual preview
British Gas BG C-2
Бренд: Valor Страницы: 35
Kalfire G Series User Instructions preview
G Series
Бренд: Kalfire Страницы: 40
Kalfire G Series Installation Instructions Manual preview
G Series
Бренд: Kalfire Страницы: 96
Valor Fires Carlton Installation Manual preview
Carlton
Бренд: Valor Fires Страницы: 8
Napoleon GD 1800-NM Installation And Operation Instructions Manual preview
GD 1800-NM
Бренд: Napoleon Страницы: 14
Desa VMH10TNB Owner'S Operation And Installation Manual preview
VMH10TNB
Бренд: Desa Страницы: 44
Sylvania SOM979PS-36AFCN Instruction Manual preview
SOM979PS-36AFCN
Бренд: Sylvania Страницы: 4
Valor Fires 341 black beauty slimline Installation And Owner'S Manual preview
341 black beauty slimline
Бренд: Valor Fires Страницы: 40
Belleze 050-HA-50128 Manual preview
050-HA-50128
Бренд: Belleze Страницы: 12
RealFlame Baltic T9650LP Owner'S Manual preview
Baltic T9650LP
Бренд: RealFlame Страницы: 72
Landmann Barrone 25282 Assembly And Use Instructions preview
Barrone 25282
Бренд: Landmann Страницы: 4
Valor G3 Classic Installation & Owner'S Manual preview
G3 Classic
Бренд: Valor Страницы: 38
Napoleon SBK4F4B3 Installation Instructions preview
SBK4F4B3
Бренд: Napoleon Страницы: 2
Napoleon ASCENT B42 Quick Start Manual preview
ASCENT B42
Бренд: Napoleon Страницы: 2
Celsi ELECTRIFLAME XD Mk2 B-1005344 Instructions Manual preview
ELECTRIFLAME XD Mk2 B-1005344
Бренд: Celsi Страницы: 12
Napoleon PRPL36 Installation Instructions preview
PRPL36
Бренд: Napoleon Страницы: 2
Valor Brava 347 Installation And Owner'S Manual preview
Brava 347
Бренд: Valor Страницы: 46
Valor intimate Owner'S Manual preview
intimate
Бренд: Valor Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды